background image

GPRS-T1 

SATEL 

  Encrypted transmission of events sent with the use of GPRS technology. 

  Notification by means of SMS messages or CLIP service about 32 selected events. 

  Periodical test transmissions for checking availability of the converter: 

–  to selected telephone numbers (with the use of SMS message or CLIP service); 

–  to monitoring stations. 

  Capability of generating additional test transmissions: 

–  after identification of the calling party's telephone number (CLIP service); 

–  after receiving command from the GPRS-S

OFT

 program. 

  Option to check the status of available resources and account validity of the SIM card 

installed in the module. 

  Indicator of GSM signal level received by industrial cellular telephone and an indicator of 

troubles connected with logging into the GSM network. 

  Output for signaling problems with logging into the GSM network. 

  Converter configuration: 

–  locally – through the RS-232 (TTL) port; 

–  remotely – through the GSM network (GPRS technology). 

  Automatic module restart. 

  Power supply with 12 V DC (±15%). 

2.  D

ESCRIPTION OF ELECTRONICS BOARD

 

 

 

Fig. 2. View of converter electronics board. 

 
Explanations for Figure 2: 

1  - 

SIM card socket.

  It is not recommended to insert the  SIM card into its socket before 

programming the card PIN code in the converter (if the card requires entering the PIN 
code).  If the  event codes are to be sent with the use of GPRS technology, the GPRS 
service must be activated for the SIM card installed in the converter. 

2  - 

LEDs

  indicating the  converter status.  LED  A  is blinking when GPRS transmission is 

going on. LED B is blinking when SMS message is being sent or the converter is calling 

Содержание GPRS-T1





















Отзывы: