Sartorius PR 5610 Скачать руководство пользователя страница 121

Страница: 121 / 165

Commissioning with Terminal

PR 5610 Installation Manual

118 Sartorius

5.3 Weighing point mask

Calling up mask

Weighingpoint

is done from the

Main Command Level

by pressing key [W].

PR1713 Rel. 03.12 20.05.2004 09:05

Weighingpoint

Max= 3000kg e= 0001kg

A < > N 0050kg

Max= 3000kg e= 0001kg

B < > N 0330kg

Max= 6000kg e= 0002kg

AB< > N 0380kg

Keys

Set Zero

Tare In/Out

Select Display

Tare

Gross

Net

Test

Flow

Zeroset

Diff

Setp

Calib/Config

Assign weighingpoints

Exit

♦

The functions of this mask are:

•

Weight display and function keys for the weighing points

•

Calling up sub-menus/ masks:

calibration / configuration

Calib/Config

weighing point assignment

Assign weighingpoints

♦

Return to the main menu is with [E]

Exit.

♦

Weight display and function keys for the weighing points.

♦

Weighing point selection (A, B or AB) is by means of the cursor up and down keys. The actually selected weighing

point is highlighted by inverse display.

If a physical weighing point has been assigned to e.g. WP B, but does not deliver valid weight data, it is
displayed as follows:

Max= 3000kg e= 0001kg

B Err 9:nocom

⇒

The function keys relate to the instantaneously selected weighing point.

Mask description.

♦

Gross/ net/ tare weight display

G/N/T Select Display

The gross, net or tare weight can be displayed by pressing the relevant key with the scale tared. This is shown by

display of the relevant letter.

♦

Setting the zero is done with key

[0]

Set Zero

When the scale was set to zero, >0< is displayed in front of the weight.

♦

Setting or erasing the tare memory is done with keys [I] or [O]

I/O Tare In/Out

♦

Press key [?] to carry out the analog test

? Test

. Test value and reply line

Toggle Testmode Status OK

instead of

the weight is displayed. Pressing key [?] once more displays the previous value again.

♦

Pressing key [P]

prints out the weight values on the printer port.

♦

Calling up mask

Assign weighing points

is done by pressing key [A]. If a production is running, this call is disabled,

message:

Production is active, no configuration possible

Содержание PR 5610






































































































































































Результаты поиска

Содержание PR 5610

Отзывы:

Бренды по названию

Популярные бренды

Sartorius PR 5610, Руководство по установке

Результаты поиска

Содержание PR 5610

Отзывы:

Бренды по названию

Популярные бренды