Sartorius PR 5610 Скачать руководство пользователя страница 115

Страница: 115 / 165

Commissioning with Terminal

PR 5610 Installation Manual

112 Sartorius

5.2.2 Set

time

Configuration Mo 05.July 2004 13:06:16

Set date

Set time

......

Enter new time [13:06:16]:

•

Press key [T]

•

The following message is displayed:

Enter new time [13: 06:16]:

•

Enter the new time e.g.:

13: 07: 00

•

Press key [

↵

], to remove the display.

•

Check against the header (top right)

5.2.3 Serial port setup

Calling up serial port setup mask

Change serial port parameter

is done from sub-menu

Configuration

pressing key [C].

PR1713 Rel. 03.12 20.05.2004 09:05

Serial port setup Mo 05.July 2004 09:31:51

Operator device: Builtin RS232 (protected)

Printer device : none

Remote device : none

Builtin: CON RS232 (locked by operating)

Slot 1: -no serial-

-no serial-

Slot 2:TTY3 RS485

........TTY4 RS232

Slot 3: -no serial-

-no serial-

PR1713 Rel. 03.12 20.05.2004 09:05

Slot 2 RS485 (TTY3) Mo 05.July 2004 09:31:51

Port :Slot 2 RS232 (TTY3)

Protocol :XON/XOFF

Baudrate : 9600

Bits : 8

Parity :None

Stopbits : 1

Devicetyp:Ansi

Echo :Enabled

⇒

When calling up this mask, the communication is disabled.

In the first mask the serial port is the selected, in the second mask the interface parameter are set. The possible
editing functions are displayed below.

•

Save configuration

Exit and save

If changes were made, the system asks e.g.:

Save Slot 2 RS485 ? (Y/N) Press [Y] or [N]

⇒

The changes are effective only after

Exit

Содержание PR 5610






































































































































































Результаты поиска

Содержание PR 5610

Отзывы:

Бренды по названию

Популярные бренды

Sartorius PR 5610, Руководство по установке

Результаты поиска

Содержание PR 5610

Отзывы:

Бренды по названию

Популярные бренды