manualshive.com logo in svg

Sapling SAP Series, Руководство по установке

Поделиться
Скачать
Sapling SAP Series Скачать руководство пользователя страница 42

1 2

3 4

42

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063 
F. (+1) 215.322.8498
www.sapling-inc.com

Flag Mount Installation - Square Clock

1) Install the double gang box in the wall or ceiling. 
If you are installing the gang box in the wall, leave 
at least eleven inches between the top of the 
gang box and the ceiling. If you are installing the 
gang box in the ceiling, leave at least eleven inches 
between the gang box and the wall. The box should 
be installed level and plumb with the wall  
and ceiling.

3) Detach the mounting plate from the mounting 
pole by unscrewing the two screws. Set the screws 
and pole aside for later.

4) Attach the mounting plate to the gang box using 
only two of the four long, silver #6-32x1 screws. 
With the mounting plate as a guide, use the pencil 
to trace the locations of the four larger holes at the 
outer corners. 

Ceiling

11” Minimum

2) Run a CAT5 or CAT6 patch cable from a PoE 
switch or PoE injector to the gang box. Confirm that 
the switch or injector, as well as the master clock, 
are connected to your network router.

KNOW YOUR NETWORK

Make sure that your network firewall is set to 
allow communication between the clocks and 
NTP servers. This means that Ports 80, 123, 
and 1777 must be open.

Содержание SAP Series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды