background image

15

CALLER ID FEATURES

To use the Caller ID you must first subscribe to your network Service
Providers' Caller ID Service. The network operator may apply a small
regular charge for this service. If you subscribe to Caller ID Service,
you can see on the display the caller's phone number (unless the
number has been withheld).
When you receive a call, the caller's telephone number will appear
the display. If the caller has withheld their number, the LCD will show
"------"or empty.
When there is an incoming call and has not been answered, the
unanswered call will be stored in the Caller ID List and the New Missed
Call Icon will be displayed.

When there is an unanswered incoming call, the caller's number is
stored in the Caller ID List. The Caller ID List holds the telephone
numbers of the last 15 unanswered calls. You can check the Caller
ID List and scroll through the list and dial numbers from the list
(described in Reviewing Caller ID List section). When there is a call
received and the calls list is full, then the oldest entry will be deleted
automatically from the memory.

Remark: If the phone number contains more than 10 digits, press
the       key will toggle the display to display the "remaining" digits.

Содержание CLT-D14









































Отзывы: