manualshive.com logo in svg

Sanyo CLT-D14, Инструкция по эксплуатации

Поделиться
Скачать
Sanyo CLT-D14 Скачать руководство пользователя страница 34

34

CALLER-ID

No Display

• Is the battery fully charged? Try to replace the batteries.
• Make sure that the base is connected to a non-switched AC

outlet. Disconnect the base from the plug and plug it in again.

• Have you subscribed to the Caller ID service from your local

telephone company? The display will not work unless you do
this.

Telephone

No dial tone

• Check installation:
- Is the base power cord connected to a working outlet?
- Is the telephone line cord connected to the base unit and the

wall jack?

- Disconnect the base from the wall jack and connect another to

the same jack. If there is no dial tone in the second phone, the
problem might be your wiring or local service.

- Is the handset out of range of the base?
- Make sure the batteries properly charged (at least 16

continuous hours).

- Are the batteries installed properly?
- Did the handset beep when you press the       ? Did the CHARGE

indicator come during battery charging? The batteries may need
to be charged.

Phone Beeps

• If it does not work, charge the batteries for 16 continuous hours.
• Replace batteries.

Dialing from memory

• Did you program the memories correctly?

TROUBLE-SHOOTING

Содержание CLT-D14









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды