Sanyo CLT-D14 Скачать руководство пользователя | Manualshive

Страница: 18 / 40

background image

18

BABY MODE

To set Baby Mode ON

1. Press the and then the [2] key.

NOTE: If the Baby Mode phone number has not been programmed,
the phone will not enter the Baby Mode and will return to STANDBY
mode.
2. The screen will show "---- "as below

3. Enter the PIN number (the default setting is "0000" if it has not

been changed)

4. Press key. The handset will enter the Baby Mode. A beep tone

will be emitted and the Baby Mode number will be flashing to
indicate the handset in the Baby Mode

To set Baby Mode OFF

1. Press the and then the [2] key.
2. The screen will show "---- " to prompt for the PIN number.
3. Enter the PIN number then followed by key.
4. The Baby Mode number will disappear from LCD and the handset

will return to normal mode.

«
...
16
17
18
19
20
...
»

Содержание CLT-D14









































Отзывы:

Нет отзывов

Похожие инструкции для CLT-D14

Бренд: Commax Страницы: 16

Бренд: Aastra Страницы: 6

ICARUS 200 SYSTEM

Бренд: Binatone Страницы: 2

Бренд: Endon Страницы: 2

Бренд: Chinavision Страницы: 18

Бренд: Panasonic Страницы: 2

KX-TD7895 - Digital Spread Spedtrum Telephone

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 41

Бренд: Panasonic Страницы: 48

KX-TD7895 - Digital Spread Spedtrum Telephone

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 52

Бренд: Panasonic Страницы: 52

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды