manualshive.com logo in svg

Sanyo CLT-D14, Инструкция по эксплуатации

Поделиться
Скачать
Sanyo CLT-D14 Скачать руководство пользователя страница 24

24

To record outgoing message (OGM)

There are two different Outgoing messages for the two answering
modes of operation, the 2-4 rings of Answering and Recording mode
and the Announce Only mode. You must record OGM before the
machine will work.

To record the Answering and Recording outgoing message (OGM1)
1. Slide the “ Ringer ” Switch at the bottom of the base unit to “ 2 ” or

“ 4 ” position.

2. Press and hold the         at the base until a beep tone is heard.
3. Speak the message for recording. The microphone is located at

the front of the base unit.

4. Press the         and beep sound will be heard for stop recording. If

the        has not been pressed, the recording will be automatically
terminated when the recording time exceeds 2 minutes.

5. The recorded message will be automatically playback for

confirmation.

6. You can always record a new message to replace the recorded

message by repeating step 2 to 4 above.

■

■

DIGITAL ANSWERING MACHINE

Содержание CLT-D14









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды