SANY SRT45 Скачать руководство пользователя страница 28

Страница: 28 / 286

Safety

Safety, Operation and Maintenance Manual

2-2

SRT45 Off-Highway Truck

2.2.12 In the event of fire ...................................................................................... 2-20

2.2.13 Windshield cleaning detergent ................................................................... 2-20

2.2.14 Precautions when using ROPS(Roll over protective structure) .................. 2-21

2.2.15 Attachment installation ............................................................................... 2-21

2.2.16 Cab windows glasses ................................................................................. 2-22

2.2.17 Unauthorized modification .......................................................................... 2-22

2.2.18 Examination and confirmation of worksite ................................................. 2-22

2.2.19 Operation on soft ground ........................................................................... 2-23

2.2.20 Overhead power cables ............................................................................. 2-24

2.2.21 Alternate exit .............................................................................................. 2-25

2.2.22 Ensure good visibilty .................................................................................. 2-25

2.2.23 Asbestos hazard ......................................................................................... 2-26

2.3 Safe Operation Precautions .................................................................................. 2-27

2.3.1 Safe starting ................................................................................................. 2-27

2.3.1.1 Safe mounting ..................................................................................... 2-27

2.3.1.2 Seat adjustment .................................................................................. 2-27

2.3.1.3 Seat belt .............................................................................................. 2-28

2.3.1.4 Before starting the engine ................................................................... 2-28

2.3.1.5 Engine starting rules ........................................................................... 2-29

2.3.1.6 Starting engine in cold season ............................................................ 2-29

2.3.1.7 Engine starting aid .............................................................................. 2-30

2.3.1.8 After starting the engine ...................................................................... 2-31

2.3.2 Operation ..................................................................................................... 2-31

2.3.2.1 Inspection before operation ................................................................ 2-31

2.3.2.2 Prior-operation precautions ................................................................ 2-31

2.3.2.3 Precautions when traveling ................................................................. 2-32

2.3.2.4 Precautions when traveling on slopes ................................................ 2-34

2.3.2.5 Precautions when operating ............................................................... 2-34

2.3.2.6 Precautions for accumulated snow, and ice ....................................... 2-34

2.3.2.7 Parking the machine ........................................................................... 2-35

2.3.2.8 Preparing the machine ........................................................................ 2-36

2.3.3 Transportation .............................................................................................. 2-37

2.3.3.1 Loading and unloading the machine ................................................... 2-37

2.3.3.2 Transporting the machine ................................................................... 2-38

2.3.4 Battery .......................................................................................................... 2-39

2.3.5 Towing .......................................................................................................... 2-41

Courtesy of Machine.Market

Содержание SRT45































































































































































































































































































Результаты поиска

Содержание SRT45

Отзывы:

Похожие инструкции для SRT45

Бренды по названию

Популярные бренды

SANY SRT45, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SRT45

Отзывы:

Похожие инструкции для SRT45

Бренды по названию

Популярные бренды