SANY SRT45 Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 286

background image

SRT45 Off-Highway Truck

3-33

Safety, Operation and Maintenance Manual

should  be  corrected  before  the  machine  is
operated  further.  Watch  the  oil  temperature
gauge  when  operating  on  upgrades,  also.  If
the  oil  temperature  goes  into  the  red  zone
(135°C  -165°C;  275°F-  392°F),  select  the
range  which  will  limit  upshifts  to  the  highest
range  in  which  the  transmission  will  operate
within  the  normal  temperature  range.  If
upshifting  must  be  consistently  limited  to
ranges lower than normal for the loads and the
grades  encountered  to  prevent  overheating
the  transmission  oil,  the  causes  should  be
determined and corrected.

3.13.4 Retrieving Diagnostic Codes

Diagnostic  fault  codes  can  be  retrieved  from
the CEC2 system using the gear shift selector
or  by  plugging  in  the  diagnostic  data  reader
(DDR). To  obtain  diagnostic  codes  using  the
gear shift selector:

※

Check transmission warning indicator on

dash will illuminate when ECU detects a fault.

※

Stop truck and select 'Neutral'.

※

Press diagnostic button (1) on gear shift

selector. Display (2) on gear shift selector will

flash one digit at a time.

※

Display starts with code position D1, D2,

etc, followed by the two digit main code, then
the two digit subcode.

※

To advance to the next code, press the

mode button (3). Up to five codes can be
stored.

※

Active codes are indicated by illumination of

the mode light (4).

3.13.5 Clearing Diagnostic Codes

To  clear  active  codes,  press  and  hold  mode
button (4) for 3 to 5 seconds.
To clear inactive codes, press and hold mode
button (4) for 8 to 10 seconds.
To  exit  diagnostic  mode,  press  diagnostic
button  (6).  Refer  to  table  for  diagnostic  code
description.

Controls and Operating

Courtesy of Machine.Market

«
...
117
118
119
120
121
...
»

Содержание SRT45































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRT45

MULTIRACK 688-S

Бренд: Garnet Страницы: 14

Бренд: Komatsu Страницы: 6

Бренд: Wittke Страницы: 87

Бренд: Noblelift Страницы: 75

ACTT Xspotter 2018

Бренд: AUTOCAR Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды