SANY SRT45 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 286

background image

Foreword

Safety, Operation and Maintenance Manual

1-1

SRT45 Off-Highway Truck

1 FOREWORD

1.1 Overview

The explanations, values, and illustrations

in  this  manual  have  been  prepared  based  on
the  latest  information  available  as  of  the  date
of  its  publication.  Continuing  improvements
in  the  design  of  this  machine  may  lead  to
additional  changes  that  are  not  reflected  in
this  manual.  Consult  SANY  or  your  SANY
distributor  for  the  latest  available  information
concerning  your  machine  or  with  questions
regarding information contained in this manual.

This manual gives details of the operation

and methods of inspection and maintenance
for this machine that must be obeyed in order
to use the machine safely. Most accidents are
caused by the failure to follow fundamental
safety rules for the operation and maintenance
of machines.

R e a d , u n d e r s t a n d a n d f o l l o w a l l

precautions and warnings in this manual and
on the machine before performing operation
and maintenance. Failure to do so may result
in serious injury or death.

SANY cannot predict every circumstance

that  might  involve  a  potential  hazard  when
the  machine  is  used.  Therefore,  the  safety
m e s s a g e s   i n   t h i s   m a n u a l   a n d   o n   t h e
machine  may  not  include  all  possible  safety
precautions.

If you carry out any operation, inspection,

or  maintenance  under  conditions  that  are  not
described  in  this  manual,  understand  that  it
is  your  responsibility  to  take  the  necessary
precautions  to  ensure  safety.  In  no  event
should you or others engage in the prohibited
uses or actions described in this manual. If the
machine is operated mistakenly when carrying
out  inspection  and  maintenance,  there  is
danger  that  it  may  lead  to  serious  injury  or
death.

Courtesy of Machine.Market

«
...
13
14
15
16
17
...
»

Содержание SRT45































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRT45

Бренд: Kalmar Страницы: 317

Бренд: UD Trucks Страницы: 385

Бренд: U-Line Страницы: 4

Бренд: Kleton Страницы: 8

Бренд: Hexagon Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды