manualshive.com logo in svg

SanDisk CompactFlash, Руководство по эксплуатации продукта

Поделиться
Скачать
SanDisk CompactFlash Скачать руководство пользователя страница 56

CompactFlash Memory Card Product Manual

SanDisk CompactFlash Memory Card Product Manual © 1998 SANDISK CORPORATION

56

6.0  ATA Command Description

This section defines the software requirements and
the format of the commands the host sends to the
CompactFlash  Memory  Cards.  Commands  are
issued to the CompactFlash Card by loading the
required registers in the command block with the
supplied  parameters,  and  then  writing  the
command  code  to  the  Command  Register.  The
manner in which a command is accepted varies.
There are three classes (see Table 6-1) of command
acceptance, all dependent on the host not issuing
commands unless the CompactFlash  Card  is  not
busy. (The BUSY bit in the status and alternate
status registers is 0.)

• Upon receipt of a Class 1  command,  the

CompactFlash  Card  sets  the  BUSY  bit
within 400 nsec.

• Upon receipt of a Class 2  command,  the

CompactFlash  Memory  Card  sets  the
BUSY  bit  within  400  nsec,  sets  up  the
sector  buffer  for  a  write  operation,  sets
DRQ  within  700  µsec,  and  clears  the
BUSY bit within 400 nsec of setting DRQ.

• Upon receipt of a Class 3  command,  the

CompactFlash  Memory  Card  sets  the
BUSY  bit  within  400  nsec,  sets  up  the
sector  buffer  for  a  write  operation,  sets
DRQ  within  20  msec  (assuming  no  re-
assignments),  and  clears  the  BUSY  bit
within 400 nsec of setting DRQ.

6.1

ATA Command Set

Table 6-1 summarizes the ATA command set with
the  paragraphs  that  follow  describing  the
individual commands and the task file for each.

Содержание CompactFlash



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды