SanDisk CompactFlash Скачать руководство пользователя страница 42

Страница: 42 / 122

CompactFlash Memory Card Product Manual

Table 4-14 Pin Replacement Changed Bit/Mask Bit Values

Initial Value

Written by Host

Final

Comments

of (C) Status

“C” Bit

“M” Bit

“C” Bit

Unchanged

Cleared by Host

Set by Host

4.4.5

Socket and Copy Register (Address 206h in
Attribute Memory)

This register contains additional configuration
information. This register is always written by

the system before writing the card’s Configuration
Index Register.

Socket and Copy Register Organization:

Operation

Read

Reserved

Drive #

Write

Drive # (0)

Reserved

This bit is reserved for future standardization. This bit must be set to zero (0) by the software when
the register is written.

Drive #

This bit indicates the drive number of the card if twin card configuration is supported.

The socket number is ignored by the CompactFlash Memory Card.

Содержание CompactFlash



























































































































Результаты поиска

Содержание CompactFlash

Отзывы:

Бренды по названию

Популярные бренды

SanDisk CompactFlash, Руководство по эксплуатации продукта

Результаты поиска

Содержание CompactFlash

Отзывы:

Бренды по названию

Популярные бренды