SanDisk CompactFlash Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 122

background image

CompactFlash Memory Card Product Manual

SanDisk CompactFlash Memory Card Product Manual © 1998 SANDISK CORPORATION

25

Table 4-2 Signal Description (continued)

Signal Name

Dir.

Pin

Description

-CSEL
(PC Card Memory Mode)

I

39

This signal is not used for this mode.

-CSEL
(PC Card I/O Mode)

This signal is not used for this mode.

-CSEL
(True IDE Mode)

This internally pulled up signal is used to configure this device
as a Master or a Slave when configured in the True IDE Mode.
When this pin is grounded, this device is configured as a
Master. When the pin is open, this device is configured as a
Slave.

D15 - D00
(PC Card Memory Mode)

I/O

31, 30, 29, 28,
27, 49, 48, 47,

6, 5, 4, 3, 2,

23, 22, 21

These lines carry the Data, Commands and Status information
between the host and the controller. D00 is the LSB of the Even
Byte of the Word. D08 is the LSB of the Odd Byte of the Word.

D15 - D00
(PC Card I/O Mode)

This signal is the same as the PC Card Memory Mode signal.

D15 - D00
(True IDE Mode)

In True IDE Mode, all Task File operations occur in byte mode on
the low order bus D00-D07 while all data transfers are 16 bit
using D00-D15.

GND
(PC Card Memory Mode)

--

1, 50

Ground.

GND
(PC Card I/O Mode)

This signal is the same for all modes.

GND
(True IDE Mode)

This signal is the same for all modes.

-INPACK
( PC Card Memory Mode)

O

43

This signal is not used in this mode.

-INPACK
( PC Card I/O Mode)
Input Acknowledge

The Input Acknowledge signal is asserted by the CompactFlash
Card when the card is selected and responding to an I/O read
cycle at the address that is on the address bus. This signal is
used by the host to control the enable of any input data buffers
between the card and the CPU.

-INPACK
(True IDE Mode)

In True IDE Mode this output signal is not used and should not
be connected at the host.

-IORD
(PC Card Memory Mode)

I

34

This signal is not used in this mode.

-IORD
(PC Card I/O Mode)

This is an I/O Read strobe generated by the host. This signal
gates I/O data onto the bus from the CompactFlash Card when
the card is configured to use the I/O interface.

-IORD
(True IDE Mode)

In True IDE Mode, this signal has the same function as in PC
Card I/O Mode.

«
...
23
24
25
26
27
...
»

Содержание CompactFlash



























































































































Отзывы:

Нет отзывов

Похожие инструкции для CompactFlash

Бренд: Qlogic Страницы: 20

Бренд: Dancover Страницы: 30

TS-h1886XU-RP-R2

Бренд: QNAP Страницы: 62

Бренд: Homak Страницы: 3

Бренд: LaCie Страницы: 26

Бренд: Rockler Страницы: 4

Бренд: Lifetime Страницы: 40

Бренд: R/Evolution Страницы: 2

MediaShare Wireless SD/USB device

Бренд: Verbatim Страницы: 21

Бренд: Verbatim Страницы: 40

Бренд: STILLA Страницы: 20

SO READY Secure

Бренд: DANE-ELEC Страницы: 2

Бренд: Rowlinson Garden Products Страницы: 5

Бренд: Karibu Страницы: 48

Бренд: red lion Страницы: 4

Бренд: Promise Technology Страницы: 63

Бренд: Draper Страницы: 4

TS-h 83XU-RP Series

Бренд: QNAP Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды