manualshive.com logo in svg

SanDisk CompactFlash, Руководство по эксплуатации продукта

Поделиться
Скачать
SanDisk CompactFlash Скачать руководство пользователя страница 102

Ordering Information and Technical Support

102

SanDisk CompactFlash Memory Card Product Manual © 1998 SANDISK CORPORATION

System Software, Card Reader/Writers and Connectors
Compatible with SanDisk CompactFlash Memory Cards

Table 1  System Software with SanDisk CompactFlash Memory Card Support

Vendor

Product Name

Telephone

Number

AMI

AMICARDZ

770-263-8181

Award/VMI

Cardware

415-968-4433

Databook

Card Talk for
Databook Chip

508-762-9779

Phoenix

Phoenix Card
Manager Plus

714-440-8000

SystemSoft

Card Soft

508-651-0088

Vadem

Socket Services for
VG365, VG465, VG468

408-467-2100

Table 2  Card Readers/Writers Compatible with SanDisk CompactFlash Memory Cards

Below is a list of PC card reader/writers that are compatible with the SanDisk CompactFlash Memory Card when
used with a passive Type II adapter. These reader/writers can be installed in desktop PCs to enable the CompactFlash
Memory Card to be used in those systems. The CompactFlash Memory Card will operate in any of these
reader/writers when used with a passive Type II adapter.

Note:

The SanDisk ImageMate, listed below, does not require use of a Type II adapter.

Vendor

Country

Telephone/FAX

Number

Product

Model

Product Type

Adtron

United States

602-926-9324
FAX 602-926-9359
http://www.adtron.com

SDDA

SDDB

SDDC

SDDL

SDDM

SDDP

SDDR

SDDS

Adapter for direct IDE-mode operation; 16-
bit data interface, BIOS compatible (no
drivers); 3.5- or 2.5-inch mount; can
replace laptop hard drives

IDE or ISA connected 8-bit drive; front
access.

Industry standard ISA dual-slot adapter,
rear entry, cabled to front entry or 100%
internal access.

External LPT port drive.

8-bit PC/104 drive.

16-bit PC/104 industry standard adapter.

External RS-232 drive.

Dual-slot SCSI bus drive; ATA card
appears as removable disk device;
compatible with PC, Macintosh and most
workstations.

Содержание CompactFlash



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды