SanDisk CompactFlash Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 122

background image

CompactFlash Memory Card Product Manual

SanDisk CompactFlash Memory Card Product Manual © 1998 SANDISK CORPORATION

14

command  is  skipped  for  the  first  16K  writes.
When  the  cycle  count  (hot  count)  of  a  sector
exceeds 16K, the system controller automatically
reverts to a full write, including the final margin
verify. Since the erase is not required in this case,
a write to a pre-erased sector with a hot count of
over 16K is still faster than to a sector that has
not  been  pre-erased.  The  Translate  Sector
command can be used to determine the “hot count”
of a sector.

1.8.6

Automatic Sleep Mode

A unique feature of  the  SanDisk  CompactFlash
Memory  Card  (and  other  SanDisk  products)  is
automatic  entrance  and  exit  from  sleep  mode.
Upon

completion

of

a

command,

the

CompactFlash Card will enter the sleep mode to
conserve  power  if  no  further  commands  are
received within 5 msec. The host does not have to
take any action for this to occur. In most systems,
the CompactFlash Memory Card is in sleep mode
except  when  the  host  is  accessing  it,  thus
conserving  power.  Note  that  the  delay  from
command completion to entering sleep mode can be
adjusted.

When  the  host  is  ready  to  access  the
CompactFlash  Memory  Card  and  it  is  in  sleep
mode, any command issued to the CompactFlash
Card will cause it to exit sleep and respond. The
host does not have to follow the ATA protocol of
issuing a reset first. It may do this if desired, but
it  is  not  needed.  By  not  issuing  the  reset,
performance is improved through the reduction of
overhead  but  this  must  be  done  only  for  the
SanDisk products as other ATA products may not
support this feature.

1.8.7

Dynamic Adjustment of Performance
versus Power Consumption

A  very  unique  and  valuable  feature  of  the
CompactFlash Memory Card is the ability of the
host to control the power the card consumes. This
allows  CompactFlash  Cards  to  work  across  a
broad  cross  section  of  platforms  without
compromising  performance.  For  instance,  it  can
operate in a platform that provides only 32 mA at
3.3  volts  average  current  (of  course  at  reduced
performance) or in a platform that provides 90 mA
at full performance. Please see the Set Features
command for details.

1.8.8

Power Supply Requirements

This is a dual  voltage  product  which  means  it
will operate at a voltage range of 3.30 volts ± 5%
or 5.00 volts ± 10% (± 5% for industrial versions).
Per the PCMCIA specification section  2.1.1,  the
host system must apply 0 volts in order to change a
voltage range. This same procedure of providing 0
volts to the card is required if  the  host  system
applies  an  input  voltage  outside  the  desired
voltage by more than 20%. This means less than
4.0 volts for the 5.00 volt range and less than 2.70
volts for the 3.30 volt range.

«
...
12
13
14
15
16
...
»

Содержание CompactFlash



























































































































Отзывы:

Нет отзывов

Похожие инструкции для CompactFlash

Kingston KIS12134

Бренд: Gardiun Страницы: 28

Glasgow KIS12992

Бренд: Gardiun Страницы: 26

StorNext QD7000

Бренд: Quantum Страницы: 29

TOWERRAID TR5M1

Бренд: Sans Digital Страницы: 82

Бренд: Facom Страницы: 2

Hybrid Home 4,8

Бренд: Hybrid Страницы: 42

Бренд: JOBO Страницы: 20

DDS Generation 6 USB

Бренд: IBM Страницы: 11

Бренд: iStorage Страницы: 23

Бренд: CalDigit Страницы: 16

Бренд: IBM Страницы: 2

Бренд: NEC Страницы: 16

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

MSA1GU2 - 1GB Memory Stick Micro M2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды