SanDisk CompactFlash Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 122

background image

CompactFlash Memory Card Product Manual

SanDisk CompactFlash Memory Card Product Manual © 1998 SANDISK CORPORATION

21

4.0 CompactFlash Memory Card Interface

Description

4.1

Physical Description

The host is connected to the CompactFlash
Memory Card using a standard 50 pin connector
consisting of two rows of 25 female contacts each on
50 mil (1.27 mm) centers.

4.1.1

Pin Assignments and Pin Type

The signal/pin assignments are listed in Table 4-1.
Low active signals have a “-” prefix. Pin types are
Input, Output or Input/Output. Table 4-2 defines
the DC characteristics for all input and output
type structures.

4.2

Electrical Description

The  CompactFlash  Memory  Card  Series  is
optimized for operation with hosts which support
the PCMCIA I/O interface standard conforming to
the  PC  Card  ATA  specification.  However,  the
CompactFlash  Card  may  also  be  configured  to
operate in systems that support only the memory
interface  standard.  The  configuration  of  the
CompactFlash Card will be controlled using the
standard PCMCIA configuration registers starting
at address 200h in the Attribute Memory space of
the CompactFlash Memory Card.

Table 4-2 describes the I/O signals. Signals whose
source is the host are designated as inputs while
signals that the CompactFlash Memory Card
sources are outputs. The CompactFlash Card logic
levels conform to those specified in the PCMCIA
Release 2.1 specification. Refer to section 4.3 for
definitions of Input and Output type.

«
...
19
20
21
22
23
...
»

Содержание CompactFlash



























































































































Отзывы:

Нет отзывов

Похожие инструкции для CompactFlash

Бренд: Data General Страницы: 91

Бренд: Secure Data Страницы: 2

Бренд: Rocsecure Страницы: 10

Бренд: GARANT Страницы: 40

TOWERRAID TR4M+

Бренд: Sans Digital Страницы: 1

Бренд: U-Line Страницы: 3

Бренд: SonicWALL Страницы: 2

Бренд: Netstor Страницы: 17

Tech Tub2 FTT600

Бренд: Copernicus Страницы: 13

Бренд: Husky Страницы: 7

actiLib Library 2U

Бренд: Actidata Страницы: 17

Intellient Stick Pro 220

Бренд: PQI Страницы: 8

Бренд: PQI Страницы: 21

Бренд: Dulce systems Страницы: 13

Multi-purpose Shed

Бренд: Tikli Страницы: 4

Бренд: Westfalia Страницы: 6

Бренд: Karibu Страницы: 48

Бренд: Supermicro Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды