manualshive.com logo in svg

S&C 5800 Series, Руководство по эксплуатации

Поделиться
Скачать
S&C 5800 Series Скачать руководство пользователя страница 9

S&C Instruction Sheet 1041-540  9

Installation

The faceplate includes the following switches:

Data Scroll Switches

Use these switches to scroll the LCD screen data into view. For more details, see “The 
Faceplate LCD Screen” section on page 10, Figure 3 on page 11, and Figure 4 on page 12.

Battery Test/Lamp Test switch

Toggle this switch to the 

Up

 position to start a battery test. The test lasts approximately 

30 seconds if the control is operating on battery power or approximately 3 minutes if the 
control is operating on ac power. The BATTERY LOW LED blinks during the test. See the 
“Power Supply/Control I/O Module” section  on page 13 for more details.
Hold this switch in the Down position to test the LEDs on the faceplate (all LEDs should 
blink).

Close/Open switch

Toggle this switch to the Up position to transmit a “Close” pulse to the line switch. Toggle 
this switch to the 

Down

 position to transmit an “Open” pulse to the switch. It is also used 

to enable

 Shots-to-Lockout

 mode. See the “Automatic Operations” section on page 21. 

Each CLOSE/OPEN switch operates one line switch.

Note: 

If the REMOTE/LOCAL switch is in the 

Remote

 position, toggling a CLOSE/

OPEN switch has no effect.

Remote/Local switch

Toggle this switch to the 

Up

 position to enable remote (SCADA) control of the line 

switch(es) and disable commands from the faceplate CLOSE/OPEN switches and 
automatic operation ENABLE/DISABLE switch.
Toggle this switch to the 

Down

 position to disable remote (SCADA) operation of the 

line switch(es) and enable commands from the faceplate CLOSE/OPEN switch(es) and 
automatic operation ENABLE/DISABLE switch. (The LOCAL LED becomes lit when this 
switch is set to 

Local

 mode.)

Note: 

To disable local automatic operation and have full control of the switch(es), 

the faceplate ENABLE/DISABLE switch must be toggled to the 

Disable

 position. If 

automatic operation is disabled on the 

SETUP: Automatic Operation

 screen (for both 

switches, if applicable), toggling the ENABLE/DISABLE switch has no effect.

Enable/Disable switch

Toggle this switch to the 

Up

 position to enable automatic switch operation of the control. 

Toggle this switch to the 

Down

 position to disable automatic operation. This switch 

affects automatic operation of both line switches, if applicable. It is also used in enabling 

Shots-to-Lockout 

mode. See the “Automatic Operations” section on page 21.

Note: 

If automatic operation is disabled on the 

SETUP: Automatic Operation

 screen 

(for both switches, if applicable), toggling this switch has no effect.

Faceplate
Switches

Содержание 5800 Series









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды