Samwontech TEMP2000 Series Скачать руководство пользователя страница 51

Страница: 51 / 91

SAMWONTECH

2nd Edition of TEMP2000_Series IM : July. 16. 2010 Page 48 / 87

▶

Following is the setup items.

①

Set Up, Down Signal Relay and Operating Deviation.

☞

Status Lamp and Relay run same way at Run Screen.

☞

For Program Run

Relay is ON until [Target Setting Point(TSP) – Set Temperature(Deviation)].

②

Soak Signal Relay and Soak Time.

☞

For Fix Operation → It displays status lamp on the screen but there is no relay output generated.

☞

For Program Operation

Status Lamp in the screen and Relay is ON until [Soak Seg Run Time(SEG TIME) – Set Temperature
(Soak Time)].

③

Set 1st, 2nd Freezer Run Signal Relay and Delay Time.

④

Set Error Signal Relay and Keep Time.

☞

Assigned Relay becomes “ON” when error occurs during Stop or Run.

☞

Relay maintains “ON” state for preset Keep Time, and becomes “OFF” after Keep Time.

☞

Relay maintains “ON” state when error is not recovered during Keep Time, and becomes “OFF” when
the error is recovered.

⑤

Set User Button Relay.

☞

Use of Button is set at [13. System Initial Setup].

☞

Corresponding Button is displayed on screen when the User Button is set.

[Figure 5-6] Aux Relay Setup Screen-2

[Figure 5-7] Aux Relay Setup Screen-3

①

②

③

④

⑤

Содержание TEMP2000 Series




























































































Результаты поиска

Содержание TEMP2000 Series

Отзывы:

Бренды по названию

Популярные бренды

Samwontech TEMP2000 Series, Руководство по установке

Результаты поиска

Содержание TEMP2000 Series

Отзывы:

Бренды по названию

Популярные бренды