Samwontech TEMP2000 Series Скачать руководство пользователя страница 40

Страница: 40 / 91

SAMWONTECH

2nd Edition of TEMP2000_Series IM : July. 16. 2010 Page 37 / 87

4.2 Retransmission Output Setup

4.2.1 Output Setup Screen-2

①

Set PID control operation method.

☞

Refer to [4.2.1.1 Operation Direction]

②

Set Cycle Time for control output operation when control output is “SSR(SOLID STATE RELAY)”.

③

Send preset Emergency Output after cutoff the PID output when STOP, S.OPN occurs.

④

Set Over-Integral Prevention Rate(Value) when over-integral prevention function is in operation.

☞

Refer to [4.2.1.3 Over-Integral Prevention]

⑤

Used to manual adjust the all PID value according to system characteristic after Auto Tuning.

☞

Control Output = PID X Control Constant (GAIN)

☞

Refer to [4.2.1.4 Control Constant]

⑥

Set upward change rate of output when control output increases.

⑦

Set downward change rate of output when control output decreases.

⑧

Move to previous or next screen using Up/Down button.

Table 4-2 Output Setup Screen-2 Parameter

Parameter

Range

Unit

Default

Operation Direction

Reverse / Forward

ABS

Reverse

Output Cycle

1~300 SEC

ABS

Emergency Output

-5.0~105.0%

0.0

Over-Integral Prevention

0.0(AUTO), 0.0 ~ 200.0%

100.0

Control Constant

0.1~10.0

ABS

1.0

Upward Change Rate

0.0(OFF) ~ 100.0 %/Sec

%/Sec

0.0(OFF)

Downward Change Rate

0.0(OFF) ~ 100.0 %/Sec

%/Sec

0.0(OFF)

①

②

③

⑤

④

[Figure 4-4] Output Setup Screen-2

⑥

⑦

⑧

Содержание TEMP2000 Series




























































































Результаты поиска

Содержание TEMP2000 Series

Отзывы:

Похожие инструкции для TEMP2000 Series

Бренды по названию

Популярные бренды

Samwontech TEMP2000 Series, Руководство по установке

Результаты поиска

Содержание TEMP2000 Series

Отзывы:

Похожие инструкции для TEMP2000 Series

Бренды по названию

Популярные бренды