Samsung SCX-6320F Скачать руководство пользователя страница 77

Страница: 77 / 208

Alignment & Adjustments

Service Manual

6-7

Samsung Electronics

6.2.5 Paper Exit Area

If the paper jams in the exit area, "Paper Jam 2" appears on the display.

1) Press the release lever to open the side cover.

2) Open the front cover.

3) Pull down on the fuser lever. This will release pres-

sure on the paper.

4) Turn the Jam Remove Lever in the direction of the

arrow to move the paper to the exit area, then gen-
tly pull the paper out through the exit area.

5) Push the fuser lever up.

6) Turn the Jam Remove Lever back to the original

position.

7) Close the front cover (1) and the side cover (2).

Содержание SCX-6320F

















































































































































































































Результаты поиска

Содержание SCX-6320F

Отзывы:

Похожие инструкции для SCX-6320F

Бренды по названию

Популярные бренды

Samsung SCX-6320F, Руководство по обслуживанию

Результаты поиска

Содержание SCX-6320F

Отзывы:

Похожие инструкции для SCX-6320F

Бренды по названию

Популярные бренды