Samsung SCX-6320F Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 208

background image

Service Manual

Troubleshooting

7-30

Samsung Electronics

White or Black

spot

• Light or dark black dots on

the image occur
periodically.

• White spots occur in the

image periodically.

1. If light or dark periodical black

dots occur, this is because the
deve rollers are contaminated
with foreign substance or paper
particles.

(1)38.3mm interval :

Charged roller

(2)94.3mm interval :

OPC cycle

2. If white spots occur in a black

image at intervals of 94.3 mm,
or black spots occur elsewhere,
the OPC drum is damaged or
foreign substance is stuck to the
surface.

3. If a black and white or graphic
image is partially broken at irregu-
lar intervals, the transfer roller's life
has been expired or the transfer
voltage is abnormal.

1. In case of 1 above -

Run OPC Cleaning Mode Print
4-5 times repeatedly to remove.
Especially check foreign sub-
stance on the OPC surface, then
remove them with a clean gauze
moistened with IPA(Isopropyl
Alcohol) not to damage OPC if
necessary.

Caution : Never use usual alcohol.

2. In case of 2 -

If they are not disappeared by
running OPC Cleaning Mode
Print 4-5 times.

: at intervals of 94.3mm -

Replace the OPC Drum.

: at intervals of 38.3mm -

Remove foreign substance,
Clean the Charged Roller

: Broken image -

Replace the toner cartridge
according to carelessness.

3. In case of 3 - Exchange the

transfer roller because the life of
the transfer roller in use has
been expired. (Check the transfer
voltage and readjust if different.)

Recycled product

• Poor appearance of the

toner cartridge and the
drum cartridge.

• Unclean and rough

printouts.

• Bad background in the

image.

1. Poor appearance of the toner

cartridge and the drum cartridge.

(1)Check the damage to label

and whether different materials
are used.

(2)Check the appearance of

parts of the toner cartridge
and the drum cartridge, such
as frame, hopper.

2. Unclean and rough printouts.

(1)Check whether foreign sub-

stance or toner are stuck to
the terminal (contact point) of
the toner cartridge and the
drum cartridge.

(2)Check whether the state of the

terminal assembly is normal.

1. In case of 1 -

(1)If there is an evidence of dis-

assembling the toner cartridge.

(2)If materials other than normal

parts of the toner cartridge are
added or substituted.

2. In case of 2 - If there are any

abnormals in connection with the
situation of 1.

(1)It occurs when the toner cartridge

is recycled over 2 times.

(2)If toner nearly being expired

are collected to use, it is judged
as the recycled toner cartridge.

Fault

Signs

Cause & Check

Solution

Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer

«
...
125
126
127
128
129
...
»

Содержание SCX-6320F

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SCX-6320F

Бренд: Wasp Страницы: 2

ApeosPort-III C7600

Бренд: Xerox Страницы: 369

Бренд: Oki Страницы: 336

Бренд: EFI Страницы: 168

VarioPrint 4110

Бренд: Oce Страницы: 216

Бренд: Ricoh Страницы: 120

Бренд: Xerox Страницы: 18

Бренд: Wasp Страницы: 2

B-510DN - Business Color Ink Jet Printer

Бренд: Epson Страницы: 2

C117001-N - DFX 5000+ B/W Dot-matrix Printer

Бренд: Epson Страницы: 229

AcuLaser CX28 Series

Бренд: Epson Страницы: 328

B-310N - Business Color Ink Jet Printer

Бренд: Epson Страницы: 4

C094001 - FX 870 B/W Dot-matrix Printer

Бренд: Epson Страницы: 11

B-310N - Business Color Ink Jet Printer

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 81

C107001 - LQ 570+ B/W Dot-matrix Printer

Бренд: Epson Страницы: 153

AcuLaser C3000 Series

Бренд: Epson Страницы: 316

AcuLaser C2800D

Бренд: Epson Страницы: 459

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды