Samsung SCX-6320F Скачать руководство пользователя страница 74

Страница: 74 / 208

Service Manual

Alignment & Adjustments

6-4

Samsung Electronics

6.2.1.2 DADF Exit Misfeed

1) Remove the remaining documents from the

DADF.

2) Open the document input tray upward and Pull

the document gently out of the DADF.

3) Close the document input tray. Then place the

documents back into the DADF.

6.2.1.3 DADF Roller Misfeed

1) Open the document cover.

2) Seize the misfed document, and remove the

document from the DADF or the feed area by
carefully pulling it towards the right using both
hands.

3) Close the document cover. Then place the

documents back into the DADF.

Содержание SCX-6320F

















































































































































































































Результаты поиска

Содержание SCX-6320F

Отзывы:

Похожие инструкции для SCX-6320F

Бренды по названию

Популярные бренды

Samsung SCX-6320F, Руководство по обслуживанию

Результаты поиска

Содержание SCX-6320F

Отзывы:

Похожие инструкции для SCX-6320F

Бренды по названию

Популярные бренды