43
CUSTOMIZING YOUR KEYSET
AME PASSWORD
This feature allows people using the AME (Answer Machine Emulation) fea-
ture to enable password protection. This will prevent unauthorized people
from listening to your messages being left. The passcode is the same as
your station passcode. This feature only applies if there is a Samsung Voice
Mail card installed in the system and your keyset has a programmed AME
key. See the Keyset User Features in the SVMi-4/SVMi-8 section.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
101
to turn on AME PASSCODE or
100
to turn it off.
•
Press
TRANSFER
to store your selection.
AUTO CAMP-ON
[iDCS 500 L/LE VERSION ONLY]
This option allows intercom calls to be automatically camped on, if possible,
when a busy station is called.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Press
081
to turn CAMP-ON on or
080
to turn it off.
•
Press
TRANSFER
to store your selection.
SELECT RING TONE
Each keyset user can select any one of eight ring frequencies:
•
While on-hook, press
TRANSFER
and then dial
111
.
•
Dial
1
–
8
or press the
UP
and
DOWN
keys to hear each tone.
•
When you hear the tone that you prefer, press
TRANSFER
to save it.
NOTE: Specific lines or stations may be programmed to ring with a dif-
ferent tone than what you have selected for your keyset.
CHANGE YOUR PASSCODE
From the factory, your station passcode is 1234. You can change your sta-
tion passcode whenever you desire.
•
While on-hook, press
TRANSFER
and then dial
101
.
•
Dial your old passcode.
•
Dial a new passcode (must be four characters). You can use
0
–
9
.
•
Redial the new passcode to verify. If successful, you will hear two beeps.
Four beeps indicate an incorrect code. Reenter the code again.
•
Press
TRANSFER
to store the new passcode.
idcs100_falcon.qxd 10/20/2004 12:42 PM Page 49
SET ANSWER MODE (INTERCOM)
You can receive internal calls in one of three modes (see
Answering Intercom
Calls
under
Intercom Calls
for descriptions):
•
While on-hook, press
TRANSFER
and then dial
103
.
•
Dial
0
for Ringing,
1
for Auto Answer or
2
for Voice Announce.
•
Press
TRANSFER
to store your selection.
NOTE: When your keyset is programmed for Auto Answer and you have For-
ward No Answer (FNA) turned on, you must answer screened transfers by
pressing the
ANS/RLS
key before your FNA timer expires or the call will for-
ward.
SET ANSWER MODE (CO)
Your incoming C.O. calls can be set to follow the intercom answer mode.
•
While on-hook, press
TRANSFER
and then dial
110
.
•
Dial
15
to access
AUTO ANS CO
.
•
Press the
VOLUME UP
or
DOWN
key to change status.
•
Press
TRANSFER
to store your selection.
AUTOMATIC HOLD
While on an outside call, pressing a line key, route key or a flashing
CALL
button will automatically put your call on hold and connect you to the next
call. This feature can be turned on or off at your keyset.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
001
to turn Automatic Hold on or
000
to turn it off.
•
Press
TRANSFER
to store your selection.
NOTE: Intercom calls can be automatically put on hold by pressing
TRANS-
FER
.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When
using headset mode, press the
ANS/RLS
key to answer and release calls.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
021
to use the headset or
020
to use the handset.
•
Press
TRANSFER
to store your selection.
Your keyset may be equipped with a Headset mode key. If it is so equipped
pressing this key while the light is out will cause the keyset to enter headset
mode and the light will illuminate to indicate this. Pressing the key while the
44
idcs100_falcon.qxd 10/20/2004 12:42 PM Page 50