Samsung DMR57 Series Скачать руководство пользователя страница 27

Страница: 27 / 71

Test Modes Part 1

Listen for fan running

Press the Delay Start key to start or stop the fan
motor.

Fan Motor
not working

Fan Motor

After temp increases 2 degrees
F, time is about 50 seconds for
each degree F increase

1. Press the Delay Start key to start or stop the

heater and the circulation pump.

2. If a low water level is sensed, water is

supplied again and the operation continues.

3. The current temperature is shown on the

display.

4. It operates up to 158ºF.

HE error

Circulation
Motor, Heater,
Thermistor

Place some cups on racks and
run circulation pump to verify
water distribution in tub.

1. Press the Delay Start key to start or stop the

pump.

2. If a low water level is detected, water is

supplied again and the operation continues.

Nozzle does
not spray

Circulation
Motor

Water fill in approximately 70
seconds average water pressure,
fills to about 1 inch past heater
shield (very little water showing
in unit)

If you press the Delay Start key, water is
drained for 45 seconds and then the water
supply starts. If the pulse count is more than
660, change the mode. Make sure to change the
mode when the pulse count is more than 660 in
t1 mode.

4E error
9E error

Inlet valve, Flow
Meter, Low
Level Sensor

Test Notes

Activate Mode

Possible

Error
Codes

Related parts

Mode

Содержание DMR57 Series








































































Результаты поиска

Содержание DMR57 Series

Отзывы:

Бренды по названию

Популярные бренды

Samsung DMR57 Series, Руководство по обучению

Результаты поиска

Содержание DMR57 Series

Отзывы:

Бренды по названию

Популярные бренды