Samsung DMR57 Series страница 26 Скачать руководство пользователя

Страница: 26 / 71

PCB TEST MODE

1) Press [Delicate] + [Rinse] + [Power] simultaneously to access this mode
2) All LED’s will illuminate then the EEPROM is tested

- If there is no issue with EEPROM, “EPA” will be displayed. If there is any issue, “Epn” will be displayed.

3) Press the “Normal" Key, to access the test modes

Note: be sure the door is closed

4) Every time you press the “Normal” Key, it changes from P1 -> P2 -> P3 -> P4.

P1 Mode : Operating part test mode. Every time you press the Delay Start Key, it toggles between run and

stop. (Cold water->Circulation Motor->Fan Motor->Drain->Dispenser-> Half Load)

P2 Mode – Not Used
P3 Mode – Not Use
P4 Mode - Touch Key, LED, Display-LED test mode.

Press each button the corresponding LED illuminates after all buttons are pressed all LED’s
illuminate momentarily.

AGING TEST MODE – Continuous Wash Mode

1) Entry method: Press the “SNormal" Key simultaneously when the power is turned on
2) After entering the mode, the display toggles between the total cycle time and total progress time repeatedly

every 1 second.
- To cancel: Turn the power off or press the SNormal keys simultaneously

Test Program Modes

Содержание DMR57 Series








































































Результаты поиска

Содержание DMR57 Series

Отзывы:

Похожие инструкции для DMR57 Series

Бренды по названию

Популярные бренды

Samsung DMR57 Series, Руководство по обучению

Результаты поиска

Содержание DMR57 Series

Отзывы:

Похожие инструкции для DMR57 Series

Бренды по названию

Популярные бренды