Samsung 2 COLOR THERMAL PRINTER SRP-275 Скачать руководство пользователя страница 9

Страница: 9 / 111

1-7

1-6

Setting up the printer

CHAPTER 1

1.8 Installing wall mount (Option)

1.7 Changing the frame control paper position

1) Turn the Set over and attach the Bracket hanger

to the Frame base then tighten four screws.

2) Attach the Bracket mount to tne wall firmly with

the eight screws. Be sure that the Bracket
attached properly to match the direction of arrow
as shown. And the Bracket mount should be
always fixed vertically.

3) Insert the Bracket hanger of Set to the Bracket

mount as shown.

1) Open the rear cover.

2) Remove the frame control paper by loosing

the two screws(3 x 6).(76 mm default)

3) Reattach the frame control paper in you want.

(Insert and tighten two screws(3 x 6) to reattach.)

4) Close the rear cover.

5) Change the Memory Switch setting for changing

paper roll width. (See the instuctions "Setting the
Memory Switches"(3.1) in Chapter 3.)

Содержание 2 COLOR THERMAL PRINTER SRP-275
















































































































Результаты поиска

Содержание 2 COLOR THERMAL PRINTER SRP-275

Отзывы:

Похожие инструкции для 2 COLOR THERMAL PRINTER SRP-275

Бренды по названию

Популярные бренды

Samsung 2 COLOR THERMAL PRINTER SRP-275, Руководство оператора

Результаты поиска

Содержание 2 COLOR THERMAL PRINTER SRP-275

Отзывы:

Похожие инструкции для 2 COLOR THERMAL PRINTER SRP-275

Бренды по названию

Популярные бренды