manualshive.com logo in svg

Samsung 2 COLOR THERMAL PRINTER SRP-275, Руководство оператора

Поделиться
Скачать
Samsung 2 COLOR THERMAL PRINTER SRP-275 Скачать руководство пользователя страница 8

1-5

1-4

1.4 Installing ribbon cassette

1) Before inserting the ribbon cassette, turn the

knob clockwise to prevent twisting the ribbon.

2) Open the front cover of printer.

3) Take out the old ribbon cassette if there is one.

4) Insert the new ribbon cassette as shown

and pay particular attention to the placement 
of the ribbon behind the Print Head.

5) During inserting the ribbon cassette, turn the

knob clockwise again to make sure the ribbon
moves freely in the cassette.

6) Close front cover of printer.

Malfunctions and other problems may arise if other than specified ribbon cassettes are
used in the printer. The Warranty may be void if other than specified ribbon cassettes are
used. Contact your dealer or place of purchase for more information about proper ribbon
cassettes.

1.5 Installing paper roll

Notice the caution label and do not touch the auto cutter blade when you open rear cover.

1) To prevent data loss, make sure that the printer

is not receiving data.

2) Open the rear cover by pushing the open button

and push the arrow mark back.

3) Remove the used paper roll core if there is one.

4) Insert the paper roll as shown.

5) Be sure to note the correct direction that the

paper should come off the paper roll.

6) Pull out small amount of paper as shown.

Then close the rear cover and tear off the extra
paper by pulling it toward the front of the printer.

Setting up the printer

CHAPTER 1

Содержание 2 COLOR THERMAL PRINTER SRP-275
















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды