Samsung 2 COLOR THERMAL PRINTER SRP-275 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 111

background image

5-27

ESC c 4

[Name]

Select paper sensor(s) to stop printing

[Format]

ASCII

ESC

c

4

n

Hex

1B

63

34

n

Decimal

27

99

52

n

[Range]

0

≤

n

≤

255

[Default]

n = 0

[Description]

Selects whether to stop printing or not when the paper runs out using
n as follows:

[Notes]

It is possible to select multiple sensors to stop printing.
When any sensor detects a paper-end, printing stops.

The paper end sensor is always enabled, and when it detects a
paper-end, the printer stops printing.

The paper near end sensor is enabled when either bit 0 or bit 1 is on
or both are on.

When a paper near-end is detected, printing stops after printing the current
line and feeding the paper.
The printer goes offline and Paper LED comes on after printing stops.
To resume printing, cancel the "paper near end" status by replacing
the paper roll.

If the roll paper near-end sensor is disabled and a paper near-end is
detected, printing does not stop and the printer does not go offline,
but the Paper LED does come on.

The settings of this command are effective until ESC @ is executed,
the printer is reset, or the power is turned off.

5-26

ESC c 3

[Name]

Select paper sensor(s) to output paper end signals

[Format]

ASCII

ESC

c

3

n

Hex

1B

63

33

n

Decimal

27

99

51

n

[Range]

0

≤

n

≤

255

[Default]

n = 15

[Description] Selects whether to output paper end signals to a parallel interface or not

when a paper end is detected by the sensor selected, using n as follows:

[Notes]

This command is enabled only with a parallel interface and is ignored
with a serial interface.

The paper near end sensor is enabled when either bit 0 or bit 1 is on
or both are on.

The paper end sensor is enabled when either bit 2 or bit 3 is on or
both are on.

When all sensors are disabled, the paper-end signal is always paper
present.

The settings of this command are effective until ESC @ is executed,
the printer is reset, or the power is turned off.

The paper near end sensor is an option. If the paper near end
sensor is not included, this printer does not detect a paper near end.

Bit

Off/On

Hex

Decimal

Function

4-7

Off
On
Off
On
Off
On
Off
On

-

00
01
00
02
00
04
00
08

-

0
1
0
2
0
4
0
8

-

Paper near end sensor disabled.
Paper near end sensor enabled.
Paper near end sensor disabled.
Paper near end sensor enabled.
Paper end sensor disabled.
Paper end sensor enabled.
Paper end sensor disabled.
Paper end sensor enabled.
Undefined

Bit

Off/On

Hex

Decimal

Function

2-7

Off
On
Off
On

-

00
01
00
02

-

0
1
0
2

-

Paper near end sensor disabled.
Paper near end sensor enabled.
Paper near end sensor disabled.
Paper near end sensor enabled.
Undefined

CONTROL COMMANDS LIST

CHAPTER 5

0

1

2

3

0

1

«
...
47
48
49
50
51
...
»

Содержание 2 COLOR THERMAL PRINTER SRP-275
















































































































Отзывы:

Нет отзывов

Похожие инструкции для 2 COLOR THERMAL PRINTER SRP-275

Бренд: 3D Systems Страницы: 17

Бренд: 3D Systems Страницы: 8

Бренд: 3D Printing Systems Страницы: 54

VarioPrint 1055

Бренд: OcÃ© Страницы: 194

Бренд: Oce Страницы: 12

Бренд: Datamax Страницы: 19

Бренд: IBM Страницы: 60

5550B - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 117

WorkCentre 3345

Бренд: Xerox Страницы: 18

Бренд: Triumph Adler Страницы: 4

Бренд: ABLE Systems Страницы: 4

Бренд: Xerox Страницы: 20

Бренд: Xerox Страницы: 150

Бренд: Avery Dennison Страницы: 2

Бренд: Xerox Страницы: 2

Бренд: Konica Minolta Страницы: 432

Бренд: Thermotron Страницы: 10

Бренд: SPRT Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды