Samsung 2 COLOR THERMAL PRINTER SRP-275 Скачать руководство пользователя страница 3

Страница: 3 / 111

Safety Precautions

In using the present appliance, please keep the following safety regulations in
order to prevent any hazard or material damage.

WARNING

Violating following instructions can cause serious injury or death.

Do not plug several products in one multi-outlet.

This can provoke over-heating and a fire.
If the plug is wet or dirty, dry or wipe it before usage.
If the plug does not fit perfectly with the outlet, do not plug in.
Be sure to use only standardized multi-outlets.

You must use only the supplied adaptor.

It is dangerous to use other adaptors.

Do not pull the cable to unplug.

This can damage the cable, which is the origin of a fire or
a breakdown of the printer.

Keep the plastic bag out of children

’

s reach.

If not, a child may put the bag on his head.

Do not plug in or unplug with your hands wet.

You can be electrocuted.

If you observe a strange smoke, odor or noise from the
printer, unplug it before taking following measures.

Switch off the printer and unplug the set from the mains.
After the disappearance of the smoke, call your dealer to repair it.

PROHIBITED

TO UNPLUG

Содержание 2 COLOR THERMAL PRINTER SRP-275
















































































































Результаты поиска

Содержание 2 COLOR THERMAL PRINTER SRP-275

Отзывы:

Похожие инструкции для 2 COLOR THERMAL PRINTER SRP-275

Бренды по названию

Популярные бренды

Samsung 2 COLOR THERMAL PRINTER SRP-275, Руководство оператора

Результаты поиска

Содержание 2 COLOR THERMAL PRINTER SRP-275

Отзывы:

Похожие инструкции для 2 COLOR THERMAL PRINTER SRP-275

Бренды по названию

Популярные бренды