Samsung 2 COLOR THERMAL PRINTER SRP-275 Скачать руководство пользователя страница 45

Страница: 45 / 111

5-18

ESC 2

[Name]

Select default line spacing

[Format]

ASCII

ESC

Hex

Decimal

[Range]

None

[Default]

None

[Description]

Sets the line spacing to the "default line spacing."

[Notes]

- The default line spacing is about 4.23 mm (1/6 inch),

which is equivalent to 12 dots.

- Selected line spacing is effective until ESC 3 is executed,

ESC @ is executed, the printer is reset, or the power is turned off.

ESC 3

[Name]

Set line spacing

[Format]

ASCII

ESC

Hex

Decimal

[Range]

≤

255

[Default]

Amount of line spacing which corresponds to "default line spacing."
(See ESC 2 for the default line spacing.)

[Description]

Sets the line spacing to n x (vertical motion unit).

[Notes]

The vertical motion unit is 0.176 mm (1/144 inch) (the minimum movement
amount). This value equals a half dot pitch. The default value is (n = 24).

When the motion unit is changed after the line spacing is set, the line
spacing setting does not change.

Selected line spacing is effective until ESC 2 is executed,
ESC @ is executed, the printer is reset, or the power is turned off.

ESC =

[Name]

Select peripheral device

[Format]

ASCII

ESC

Hex

Decimal

[Range]

≤

[Default]

n = 1

[Description]

Selects the device to which the host computer sends data, using n as follows:

[Notes]

When the printer is disabled, it ignores all received data and commands
with the exception of ESC = and real-time commands.

If ASB is enabled when the printer is disabled by this command, the printer
transmits the ASB status message whenever the status changes.
See the description of GS a for ASB function.

Settings of this command are effective until the printer is reset, or the power
is turned off.

5-19

ESC <

[Name]

Return home

[Format]

ASCII

ESC

Hex

Decimal

[Range]

None

[Default]

None

[Description]

Moves the print head to the standby position.

[Notes]

The standby position is on the left.

The command rechecks the standby position ;
therefore, the print position might be shifted before and after checking the
standby position.

1
2
3

Function

Enables the printer

Disables the printer

Enables the printer

CONTROL COMMANDS LIST

CHAPTER 5

Содержание 2 COLOR THERMAL PRINTER SRP-275
















































































































Результаты поиска

Содержание 2 COLOR THERMAL PRINTER SRP-275

Отзывы:

Похожие инструкции для 2 COLOR THERMAL PRINTER SRP-275

Бренды по названию

Популярные бренды

Samsung 2 COLOR THERMAL PRINTER SRP-275, Руководство оператора

Результаты поиска

Содержание 2 COLOR THERMAL PRINTER SRP-275

Отзывы:

Похожие инструкции для 2 COLOR THERMAL PRINTER SRP-275

Бренды по названию

Популярные бренды