Samlexpower PSE-12125A Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 52

background image

44 | SAMLEX AMERICA INC.

seCtIOn 12 |

troubleshooting Guide

SYMPtoM
There is no Ac output. The voltage lEd bar graph (d, fig. 7.1 or 7.2) shows dc input
voltage reading of 15V (full bar graph is lighted up to the top rEd lEd).
PoSSiBle cAUSe

Shut-down due to high input dc voltage (>16.5V). The unit will re-set automatically
when the voltage drops below 16.5V.
Remedy:
1. check that the voltage at the dc input terminals is less than 16.5V.
2. Ensure that the maximum charging voltage of the battery charger /
alternator / solar charge controller is below 16.5V.
3. Ensure that an un-regulated solar panel is not used to charge a battery. under
cold ambient temperatures, the output of the solar panel may exceed 16.5V.
Ensure that a charge controller is used between the solar panel and the battery.

SYMPtoM
The Ac output drops momentarily and rises to normal automatically. red overload
lEd (c, fig. 7.1 or 7.2) is not lighted (might happen during starting of certain loads).
PoSSiBle cAUSe

Temporary drop-in Ac output voltage due to surge power overload within the
Surge Power rating of the inverter.

SYMPtoM
The Ac output shuts down completely. The red overload lEd (c, fig. 7.1 or 7.2)
is lighted.
PoSSiBle cAUSe

Permanent shut-down of the Ac output due to continuous overload beyond the
continuous / surge power rating of the inverter. note: The unit will be latched in
this shut-down condition. To reset, switch the power on /off switch to off and
then on again. before switching on again, remove the cause of the shut-down.
Remedy:
1. reduce the load.
2. The load is not suitable as it requires higher power to operate. use an inverter
with higher power rating.
3. If the unit goes into permanent overload again after resetting and removing
the load completely, the unit has become defective. call Technical support.

«
...
42
43
44
45
46
...
»

Содержание PSE-12125A





















































Отзывы:

Нет отзывов

Похожие инструкции для PSE-12125A

Бренд: Growatt Страницы: 45

Бренд: LEGRAND Страницы: 4

Бренд: Moxa Technologies Страницы: 2

Бренд: EINHELL Страницы: 10

Бренд: Inorea Страницы: 104

Evolute RTLA50-S

Бренд: Renishaw Страницы: 11

Бренд: CEL-MAR Страницы: 28

Бренд: B&B Electronics Страницы: 2

Бренд: LogicLadder Страницы: 55

Бренд: CYP Страницы: 16

Бренд: Analog Devices Страницы: 10

Бренд: Lindy Страницы: 14

ECO Inverter+ 7

Бренд: Oilon Страницы: 58

SINEMASTER IG4300

Бренд: Kipor Страницы: 50

GTB-UHD600-18S-RT

Бренд: Gefen Страницы: 56

Бренд: Omnitron Systems Technology Страницы: 1

Pro Power SB Series

Бренд: Sterling Power Страницы: 8

3D Vision Encoder

Бренд: ADJ Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды