Samlexpower PSE-12125A Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 52

background image

44 | SAMLEX AMERICA INC.

SAMLEX AMERICA INC. | 45

seCtIOn 12 |

troubleshooting Guide

SYMPtoM
buzzer alarm is sounded. red over Temp lEd is on (b, fig. 7.1 or 7.2).
There is no Ac output.
PoSSiBle cAUSe

Shut-down due to over temperature because of fan failure or inadequate
cooling as a result of high ambient temperature or insufficient air exchange.
Remedy:
1. check that the fan is working. If not, the fan / fan control circuit may be
defective. call Technical Support.
2. If the fan is working, check that the ventilation slots on the suction side
(l, fig. 7.1 or 7.2) and the openings on the discharge side of the fan
(g, fig. 7.1 or 7.2) are not obstructed.
3. If the fan is working and the openings are not obstructed, check that enough
cool replacement air is available. Also check that the ambient air temperature
is less than 40ºc / 104ºf.
4. reduce the load to reduce the heating effect.
5. After the cause of over heating is removed and the unit cools down, it will
reset automatically.

«
...
43
44
45
46
47
...
»

Содержание PSE-12125A





















































Отзывы:

Нет отзывов

Похожие инструкции для PSE-12125A

Бренд: Net Optics Страницы: 15

Бренд: Prism Sound Страницы: 63

Бренд: TRUELOOK Страницы: 12

Бренд: WORMS Страницы: 52

Бренд: Eaton Страницы: 86

Бренд: Sabrent Страницы: 7

Бренд: DROPSA Страницы: 8

SM-Universal Encoder Plus

Бренд: Control Techniques Страницы: 112

Бренд: Kiloview Страницы: 50

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Delta Страницы: 4

Бренд: Black Box Страницы: 54

Бренд: VuPoint Страницы: 25

Бренд: CYP Страницы: 88

Бренд: SRS Lighting Страницы: 4

Бренд: TE Страницы: 40

Бренд: Singmai Electronics Страницы: 26

ATEX Splitter Box

Бренд: Wolf Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды