Samlexpower PSE-12125A Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 52

background image

42 | SAMLEX AMERICA INC.

SAMLEX AMERICA INC. | 43

seCtIOn 12 |

troubleshooting Guide

SYMPtoM
low Ac output voltage and the input current lEd bar graph (d, fig. 7.1 or 7.2) shows
very high current (no buzzer alarm).
PoSSiBle cAUSe

low voltage at the dc input terminals and the load is close to the maximum
allowable power.
Remedy:
1. check that the battery is fully charged. recharge, if low.
2. check that the battery cables are thick enough to carry the required current
over the required length. use thicker cables, if required.
3. Tighten connections of the battery input circuit.
4. reduce the load.

SYMPtoM
buzzer alarm is sounded when load is switched on. dc input voltage lEd bar graph
(d, fig. 7.1 or 7.2) reads between 10 and 10.5V. Ac output voltage is available.
PoSSiBle cAUSe

low input voltage at the inverter terminals and the load is close to the maximum
allowable power.
Remedy:
1. check that the battery is fully charged. recharge, if low.
2. check that the battery cables are thick enough to carry the required current
over the required length. use thicker cables, if required.
3. Tighten connections of the battery input circuit.

SYMPtoM
buzzer alarm is sounded when load is switched on. dc input voltage lEd bar graph
(d, fig. 7.1 or 7.2) reads below 10V. There is no Ac output.
PoSSiBle cAUSe

Shut-down due to low input dc voltage (less than 10V). note: The unit will re-set
automatically when the input voltage rises to 11.3V.
Remedy:
1. check that the battery is fully charged. recharge, if low.
2. check that the battery cables are thick enough to carry the required current
over the required length. use thicker cables, if required.
3. Tighten connections of the battery input circuit.

«
...
41
42
43
44
45
...
»

Содержание PSE-12125A





















































Отзывы:

Нет отзывов

Похожие инструкции для PSE-12125A

Бренд: Zenith Страницы: 54

Бренд: Lenze Страницы: 132

Бренд: Mutec Страницы: 22

AT-IMC100T/SCMM

Бренд: Allied Telesis Страницы: 20

Бренд: Fenner Страницы: 12

Бренд: 3onedata Страницы: 3

QM1003-0.5-18-2

Бренд: Quonset Microwave Страницы: 100

Бренд: Systech Corporation Страницы: 6

HDMI to YUV/YPbPr

Бренд: J.S. Technology Страницы: 2

Бренд: CYP Страницы: 23

Бренд: Advent Страницы: 110

Бренд: Aurora Design Страницы: 2

Бренд: Mitsubishi Страницы: 96

BIT COMMANDER US2000A

Бренд: U.S. Converters Страницы: 24

Бренд: Vanner Страницы: 16

Soundtouch Stereo JC

Бренд: Bose Страницы: 34

Бренд: Weidmuller Страницы: 13

ControlVIT CV10 series

Бренд: Salicru Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды