Saia PCD2.H310 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 154

background image

Installation and commissioning

PCD2.H31x

Page 9-10



SAIA-Burgess Electronics Ltd.

(2H3-09-E.DOC)

26/762 E2

9.4.5

PID controller

To check and tune the PID controller, the following preconditions must
be met:

•

With the controller powered off, the control circuit is closed by re-
connecting the setpoint cable of the power stage to terminals 6 and
GND of the H3 module.

•

Power up the controller:
CAUTION: Activate emergency stop if the axis should proceed out of
control.

•

The programming unit is connected and commissioning software has
been started.

Checks:

1.

Load destination position 0 and execute start instruction.

→

The H3 module regulator is switched on and the axis is held in

its position by the regulator.

2.

Load a destination position that is located within the allowed trav-
elling range and start motion.

→

The axis runs towards the fixed destination position.

Incorrect behaviour:

•

The axis runs at maximum velocity.

Possible cause

•

Position control circuit (H3 module) or speed control
circuit (power stage) incorrectly poled.
This means that, when the setpoint voltage is posi-
tive (= positive destination position) motion in the
axis is in a negative direction.

•

The H3 module’s analogue output is faulty and sup-
plies a constant, maximum voltage of approx. +12V
or –12V to the controller output.

Remedy

•

Check direction, execute section 9.4.4 once again
and make the necessary changes to poling.

•

Change the H3 module.

«
...
74
75
76
77
78
...
»

Содержание PCD2.H310



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для PCD2.H310

Бренд: ABATEC Страницы: 8

Бренд: CALEFFI Страницы: 2

Бренд: CALEFFI Страницы: 12

Бренд: Caliber Страницы: 6

Бренд: EasyIO Страницы: 18

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 35

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 73

Бренд: Eaton Страницы: 4

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 14

Бренд: Eaton Страницы: 36

Бренд: IDK Страницы: 96

Бренд: Kärcher Страницы: 4

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды