background image

SAFEGREASE, SAFEOIL, MULTILUBE 
ST-1340 
 

 

13401BEN.doc 

27.12.2004  Rev. 1B 

 

CONTROL CENTER ST-1340 

TABLE OF CONTENTS 

1 GENERAL DESCRIPTION ................................................................................................................................1

 

2 DESIGN .............................................................................................................................................................1

 

2.1 Control panel...............................................................................................................................................1

 

2.2 Channel module CM1440 ...........................................................................................................................2

 

2.2.1 General.................................................................................................................................................2

 

2.2.2 LED-signals ..........................................................................................................................................3

 

3 OPERATION......................................................................................................................................................4

 

3.1 Normal mode...............................................................................................................................................4

 

3.1.1 Basic display ........................................................................................................................................4

 

3.1.2 Phase codes for normal mode and alarm mode ..................................................................................6

 

3.2 Extra lubrication ..........................................................................................................................................7

 

3.3 Manual operation ........................................................................................................................................7

 

3.4 Lubrication cycle counter ............................................................................................................................9

 

3.5 Power failure .............................................................................................................................................10

 

3.6 Alarms .......................................................................................................................................................10

 

3.6.1 Low level alarm ..................................................................................................................................10

 

3.6.2 Pressure alarm ...................................................................................................................................11

 

3.6.3 Power failure alarm ............................................................................................................................11

 

3.6.4 Error alarm from electronics ...............................................................................................................11

 

3.6.5 Channel-specific alarm relay ..............................................................................................................12

 

3.6.6 Center-specific alarm relay.................................................................................................................12

 

4 SETTINGS .......................................................................................................................................................12

 

4.1 General......................................................................................................................................................12

 

4.2 Settings display .........................................................................................................................................13

 

4.3 Settings mode ...........................................................................................................................................14

 

4.4 Set value limits ..........................................................................................................................................16

 

4.5 Configuration display.................................................................................................................................16

 

5 TECHNICAL SPECIFICATION........................................................................................................................18

 

5.1 Technical specifications ............................................................................................................................18

 

5.2 Connections ..............................................................................................................................................19

 

5.3 Symbols ....................................................................................................................................................19

 

6 SPARE PARTS................................................................................................................................................19

 

 

   2 APPENDICES 

Содержание ST-1340























Отзывы: