background image

SAFEGREASE, SAFEOIL, MULTILUBE 
ST-1340 
 

 

13401BEN.doc 

27.12.2004  Rev. 1B 

16 (19) 

 

4.4   Set value limits 

Lubrication cycle can be set within 1 min - 999 h 59 min. In grease lubrication channels, 
pumping is started twice during one lubrication cycle. In oil lubrication channels pumping is 
started once during one lubrication cycle. 

Maximum pressurization time can be set within 0 s - 9999 s. The channel can be closed by 
entering 0 s for maximum pressurization time, in which case lubrication is not performed. 

In pressure transmitter channels the pressure high limit can be set within 0 - 160 bar. The 
pressure low limit can be set between 0 bar and the set pressure high limit. 

4.5   Configuration display 

Channel configuration settings are displayed by selecting 

Page

 - 

Othr

 - 

Conf

 at the basic 

display. 

 

CH2 SG2 Machine 1

 

Group 1 Pump CH12

 

Relay  0  P-transm.

 

Chnl  ---- Set  Esc

 

Figure 11. 

Configuration display 

Display lines 

Note 

The texts in brackets are sample display texts. 

 

The first line indicates the selected channel 

 number 

(

CH2

 

operation mode (

SG2

 name 

(

Machine 1

 

The second line indicates the selected channel 

 group 

(

Group 1

 

pump control channel (

Pump CH2

 

The third line indicates the selected channel 

 

the operation mode for channel-specific alarm relay (

Relay 0

 

pressure control unit type (

P-transm.

 

The fourth line indicates 

 

the function key texts 

Содержание ST-1340























Отзывы: