background image

SAFEGREASE, SAFEOIL, MULTILUBE 
ST-1340 
 

 

13401BEN.doc 

27.12.2004  Rev. 1B 

10 (19) 

 

Display function keys 

Key Description 

Chnl

 Channel 

selection 

Press key to display the lubrication cycle counter for the next channel. 
Channel can also be selected with 

Í

 and 

Î

 keys, which can used for toggling 

between channel up and down. 

Clr

 Counter 

reset 

Press key to reset counter. The program requires a password (

1340 

or

 1440

before it resets the counter. The counter reset time is saved and it is displayed. 

Esc

 

Back to basic display 

3.5   Power failure 

The set values and program status are preserved in the memory also during power failures. 
After power is back on, the center will resume from the status it was before power failure 
occurred. Possible paused pressurization is re-started for the same line. Interval times are not 
counted during power failures. 

3.6   Alarms 

The center is in alarm mode, when the red 

Alarm

 LED-signal on the cover is lit. 

Channel specific alarms are visible in channel module 

AL

 LED-signals and in the channel basic 

displays. 

Press the 

Ack

. key for the channel in question to reset the alarm. 

Note 

The alarm can be reset only after the problem causing the alarm has been 
resolved. 

After the alarm has been successfully reset, the channel will perform the lubrication cycle as 
soon as it is possible due to delays and the pressurization of other channels. 

  

CH2 SG2 Machine 1

  

Press.al. L1 0020min

  

L1:085bar L2:005bar

  

Chnl Page  Ack. Manu

 

Figure 7. 

Basic display, pressure alarm 

3.6.1   Low level alarm 

The channel triggers a low level alarm, pauses pressurization and forces the center into alarm 
mode, if the lubricant barrel is empty which means that the low level switch is closed. In this 
case, a phase code 

Low level

 and the elapsed alarm time are displayed. Also the channel 

module LED-signals 

LO

 and 

AL

 are lit. The same line will be pressurized again, when low level 

switch is open and the alarm has been reset by pressing the 

Ack. 

key for the channel in 

question. The channel low level alarm mode does not affect the operation of other channels. 

Содержание ST-1340























Отзывы: