Sabo 43-EL COMPACT, Руководство оператора

Страница: 35 / 72

9
Replacing the blade
WARNING
The cutter bar must always be replaced by an authorised workshop since an
insulation protection test always has to be carried out after repairs and
maintenance work on insulation parts (e.g. blade screw) in accordance with the
applicable standard DIN EN 60335.
In addition, a wrongly assembled cutting blade coupling can allow the cutter bar
to become loose, which can lead to serious injuries.
– Only use genuine cutter bars for replacement. Non-equivalent spare parts can
damage the machine and are a safety hazard.
– Replacement cutting tool must be marked permanently with the name and/or
company logo of the manufacturer or supplier and the part number.
Servicing the wheels (Illustration S )
Lubricate the wheel bearings once a year or every 15-20 operating hours.
– Remove the wheel caps S .
– Use a socket wrench to loosen the hexagon nut, washer and wheels.
– After the bearings have been lubricated with roller bearing grease "KAJO-Longlife
grease LZR 2", push the wheels back in place, replace the washer, fix the hexagon
nut and tighten until the wheels can just about turn easily but without play. Replace
the wheel caps.
17 TROUBLESHOOTING
Fault Possible cause Remedy
If the motor does not
start 5 seconds after
the unit is started
No power supply. Connect the plug C2 .
Check the fuse.
Power cable damaged. Get it checked by an
authorised workshop.
Cutting height has been
set too low (grass is too
high and blocks the
starting of the motor). Set a higher cutting height I .
Machine tilts when starting it.
Too much grass waste in
the housing. Clean the cutting chamber of
grass, ensure that the gap
between fan and housing is
kept clean (pull the plug
first!).
Get it checked by an
authorised workshop.
Extreme vibration
Have it checked by an
authorized dealer
Unclean cut, lawn is
yellow
Blade blunt.
Have it sharpened and
balanced by an authorized
dealer
Q .
Cutting height too low. Adjust to higher cutting height
I .
Mowing too fast. Adjust mowing speed.
Insufficient overlapping
of cuts when mowing. Tall grass conditions may
dictate that more overlapping
of cuts is required.
Lawn becomes matted. A lawn scarifier can remedy
the problem considerably
Ejection blocked
Turbo signal has not
been detected
J + K .
Empty the grass collector L .
Cutting height too low for
grass that is too high. Adjust to higher cutting height
I .
Pushing mower too fast. Adjust mowing speed.
Grass not dry. Let grass dry.
Repairs to electrical machines must always be performed only by qualified electricians.
Please do not repair them yourself.
In the case of faults and defects which have not been listed here, please contact the
nearest authorized dealer. This applies in particular to appliances with electrical motors,
as when these are repaired they must always undergo an insulation protection test.
Your authorized dealer will also help you if you do not wish to perform any of the
maintenance work described here yourself.
18 TECHNICAL DATA
Motor
Motor Alternating current motor
Connection voltage 230 V
Power 1500 W
Motor speed 3000 min
-1
Mower
Housing Die-cast aluminium
Cutting width 430 mm
Cutting heights Central, 22, 30, 35, 42, 50, 60, 80 mm
Adjustable-height handlebar 3-way
Grass collector capacity 55 litres
Weight 27 kg
Length 1480 mm
Width 500 mm
Height 1000 mm
Wheels front / rear Ø 180 mm / Ø 180 mm
Bearing front Cup-and-cone bearing
Bearing rear Cup-and-cone bearing
Sound power level
Guaranteed sound power level;
measured according to 2000/14/EC L
wa
= 96 dB(A)
Sound pressure level
Emission sound pressure level at operator's workplace;
measured according to EN60335-2-77
Measuring inaccuracy; according to ISO 4871 L
pA
= 82 dB(A)
1.5 dB
Vibrations
Vibrations on the lawnmower’s ha ndlebar;
measured according to EN 60335-2-77
Measuring inaccuracy; according to EN12096
a
hW
= 1 m/s
2
0.5 m/s
2
19 ORIGINAL SPARE PARTS
Roller bearing grease SAA11300
Cutter bar For safety reasons, the cutter bar must
always be replaced by an authorised
workshop.
This workshop has the respective spare
part numbers for the cutter bar available.