Rytan RY256 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 39

background image

33

2. Your drive belt is coming apart or is frayed. Replace it.

3. Your ball bearing cutter wheel shaft assembly is wearing out. With the machine turned

OFF—grab the cutter wheel’s left-hand nut and try to get some movement out of it. There
should be absolutely no movement—if there’s movement in the bearings you need to replace
the cutter shaft assembly. If there is not movement it may be the other bearing next to the
drive pulley—you will have to remove the drive belt to be able to check it out. If all seems
well then you’re probably O.K. for a while.

4. The machine’s cutter shaft lock is partially depressed and is rubbing against the drive pulley.

Pull up on the shaft lock knob.

Machine Won’t Start

There are several things that can cause this besides the obvious—plug in the machine and check the
power line.

1. If you are running 12 Volt D.C.—check the fuse and ALL the wiring and connections.

2. Key cuttings in the motor’s capacitor. Unplug the machine, remove the capacitor’s rubber

cover and blow out the chips. Remember to wear safety glasses.

3. Remove the machine’s access plate—check the wiring connections and switch. Repair or

replace as necessary.

4. Cutter shaft lock is in the locked position.

Can’t Make Depth Adjustment

The problem is you’ve run out of room in the stylus assembly to make the adjustment because
You have one stop vise jaw in the standard configuration and other top vise jaw in the step
configuration.

1. Make sure both are install in the standard configuration and should be O.K.

2. You’ve had your cutter resharpened to many times and the diameter is too small to work on

your machine.

Cutter Wheel Didn’t Seem to Last Long

Several things can cause this to happen.

1. The cutter will last the longest if it only duplicates brass keys.

2. Premium quality Nickel-Silver key blanks are abrasive to the cutter wheel and will dull the cutter

more rapidly than brass keys. Here’s what you can do to get the maximum life out of your cutter
wheel on these premium blanks.

a) Duplicate them a little slower. Racing through the job, especially in large rekeying jobs will put

more wear on the cutter wheel than going a little slower. The machine’s high-speed “stick-shift”
feature, extremely powerful motor and extra large diameter cutter are a real temptation to push the
machine faster and faster.

b) You should charge a little bit more money for cutting premium key blanks and put that difference
aside for the purchase of a new cutter.

«
...
31
32
33
34
35
...
»

Содержание RY256








































Отзывы:

Нет отзывов

Похожие инструкции для RY256

Бренд: All Pro Solutions Страницы: 16

Бренд: All Pro Solutions Страницы: 51

Бренд: All Pro Solutions Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды