RSP M0720-1 Скачать руководство пользователя страница 25

Страница: 25 / 64

M0720-1 ver 3.4

3.3 Sparking

WARNING!

Electrical signals and power must be switched off and disconnected

when docking the tool attachment. This is to prevent sparking between signal pins
and tool attachment.

3.4 Programming

The following will ensure a correct docking position.

Action

Attach a spare tool attachment to the tool changer.

Position the spare tool attachment above the tool attachment that is mounted at the tool.

The correct position is f ound when the tool attachments are parallel, centered and the
engraved arrows are on the same line.

Save the position. The robot can move to this position with high speed.

Dismount the spare tool attachment.

Go back to the saved position and move the tool changer (in axis 6 direction) the remaining
distance to the tool attachment (mounted at the tool).

Save the position. The robot should move the f inal distance to this position with low speed.

3.5 Tool Stand

NOTE!

To guarantee reliability and a long service-life for the tool changer, the tool stand
must be stable, both in terms of its design and attachment.

NOTE!

The tool stand must not be spring-loaded!

3.6 Tool Identification

Jumpers on signals at the tool attachment can be used to give information about which tool
attachment that is docked in the tool changer.

Содержание M0720-1

































































Результаты поиска

Содержание M0720-1

Отзывы:

Похожие инструкции для M0720-1

Бренды по названию

Популярные бренды

RSP M0720-1, Руководство по установке и обслуживанию

Результаты поиска

Содержание M0720-1

Отзывы:

Похожие инструкции для M0720-1

Бренды по названию

Популярные бренды