RSP M0720-1 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 64

background image

M0720-1 ver 3.4

39

5.2 Forced manual unlocking, P6910

In case the tool attachment is jammed and mechanically stuck to the tool changer, the tool
attachment can be released using a forced opening kit and a grease gun. Such forced opening
kit, with product number P6910, can be obtained from Robot System Products.

NOTE!

Forced manual unlocking shall only be carried out when tool attachment is stuck to
the tool changer and cannot be released through other means.

Action

Note

1

Safety

Read the saf ety section (1.2).

2

Position robot and tool

Place robot in position f or
undocking of tool attachment
and tool.

NOTE!

Make sure the tool

attachment and tool are f ully
supported by a tool stand or
table.

3

Pneumatic air off

Switch of f the pneumatic air.

NOTE!

The air pressure must

be f ully relieved bef ore
dismounting.

4

Remove plug

Unscrew and remove the
protection plugs from the two
connections f or manual
unlocking using an Allen key.

NOTE!

The connections f or

manual unlocking are
positioned diagonally across
the tool changer.

6

Connect forced opening kit

Screw the two coupling
extenders to each dedicated
position on the tool changer.

NOTE!

The coupling extenders

are included in the f orced
opening kit (P6910).

«
...
37
38
39
40
41
...
»

Содержание M0720-1

































































Отзывы:

Нет отзывов

Похожие инструкции для M0720-1

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

Бренд: 3M Страницы: 2

Бренд: Paia Страницы: 11

Бренд: CAB Страницы: 39

Бренд: CAB Страницы: 27

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренд: V.ORLANDI Страницы: 144

Бренд: GE Страницы: 18

Бренд: Valko Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды