RSP M0720-1 страница 41 Скачать руководство пользователя

Страница: 41 / 64

M0720-1 ver 3.4

6 DISMOUNTING AND REPLACEMENT

6.1 Replacement of tool changer

Action

Note

Safety

Read the saf ety section (1.2).

Dismount tool

Leave tool, with tool
attachment mounted, in tool
stand.

Service position

Place the robot in service
position.

NOTE!

The tool change

f unction shall be in locked
position.

Power off

Switch the power of f and lock
the circuit breaker.

NOTE!

Read the saf ety

chapter f or the robot.

Pneumatic air off

Switch of f the pneumatic air.

NOTE!

The pressure in the

pneumatic system must be
released bef ore dismounting
begins.

Dismount hoses

Dismount the water/air hoses
f rom the tool changer

NOTE!

Make sure that no dirt

enters the air hoses.

Disconnect electric connections

Disconnect electric power
and signals.

NOTE!

Handle the contacts

with care, as they are
sensitive to mechanical
damage. Make sure that no
dirt enters the contacts.

Содержание M0720-1

































































Результаты поиска

Содержание M0720-1

Отзывы:

Похожие инструкции для M0720-1

Бренды по названию

Популярные бренды

RSP M0720-1, Руководство по установке и обслуживанию

Результаты поиска

Содержание M0720-1

Отзывы:

Похожие инструкции для M0720-1

Бренды по названию

Популярные бренды