INSTALLATION REPORT
S7 / S8 A & M SERIES
OFFICE USE ONLY
Route to: Servicer Mgr Accounting Andy Accounting
Warranty Exp Date
________
REV 031617
ROTTLER MANUFACTURING MUST HAVE THIS REPORT RETURNED
TO PROPERLY QUALIFY WARRANTY ON EQUIPMENT
Customer:____________________________ Address:_______________________________________
City:_________________________________ State:_____ Zip:_________ Phone:_______________
Country:______________________________
Machine Model:___________ Serial Number:__________ Representative:________________________
MACHINE INSTALLATION:
Electrical information MUST be complete to validate this report.
______Follow instructions in this section to uncrate, unpack, and prep machine.
VERY IMPORTANT:
Modern design machines contain electronic low voltage
circuitry that provides great advantages and a better machine life. BUT, you
must have an excellent, stable, isolated power supply along with an isolated
ground. If not, electrical noise problems are likely to interfere with machine
operation unexpectedly.
Customer is responsible for providing electricity to machine in a manner that meets the local
electrical code requirements.
______Check machine with precision level and for equal support on feet, then carefully adjust supports to
precisely secure the best average flatness of the top table.
______This machine requires 208 to 240V AC 1-phase, 50/60HZ, isolated power supply (measured
between L1 and L2). Current requirement is 15 amps. When using two legs of a three-phase
supply, the voltage from each leg to ground must be between 100-120V AC. Measure the
voltages of the power supply twice during installation (1) _______VAC (2) ________VAC.
IF VOLTAGE IS OUTSIDE THE CORRECT RANGE AT ANY TIME THE
MACHINE WILL NOT OPERATE PROPERLY AND MAY BE DAMAGED.
______Briefly describe the isolated ground connection you have made: (Instructions to make a correct
ground are included with the manual
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
Содержание S7A
