background image

Operating Manual - 

EVO

®

 Line

[en] 07/2020

1.1

1

Foreword

1.1 General

This manual contains information and regulations 

for the installation and operation of the screw com-

pressor air ends EVO2, EVO3, EVO3-G, EVO6, 

EVO6-G, EVO9, EVO9-G, EVO15, EVO15-G, 

EVO28, EVO28-G, EVO42 and EVO42-G.

1.2 Scope

This documentation is applicable for screw com-

pressor air ends of the models EVO2, EVO3, 

EVO3-G, EVO6, EVO6-G, EVO9, EVO9-G, 

EVO15, EVO15-G, EVO28, EVO28-G, EVO42 

and EVO42-G from delivery date.

1.3 Change service

This document is not subject to the change ser-

vice.

1.4 Abbreviations 

bar (g)

Operating pressure 

(relative pressure in bar)

Bh

Operating hours

DHV

Minimum pressure valve

RC

ROTORCOMP

SIV

Safety valve

Min.

minimum

Max.

maximum

V DC

Direct voltage

V AC

Alternating voltage

1.5 Manufacturer's information

1.5.1 General information

This operating manual provides information on the 

operating principles, installation, operation and 

maintenance of the screw compressor air ends.

Read this operating manual carefully before com-

missioning the screw compressor air ends for the 

first time in order to ensure proper handling, oper-

ation and maintenance from the outset.

Please observe all warnings and safety instruc-

tions.

ROTORCOMP screw compressor air ends are 

carefully checked and tested prior to shipping. 

When your merchandise arrives, the delivery 

scope must be checked for completeness and 

possible damage. Any missing parts and/or trans-

port damage must be reported immediately.

A damaged screw compressor air end must not be 

put into operation under any circumstances.

Always have the operating manual available for 

the operating personnel and make sure that oper-

ation and maintenance are carried out according 

to the instructions.

All instructions contained in this operating manual 

must be observed in the specified manner and 

sequence in order to prevent injuries and damage 

to the system.

The screw compressor air ends has been built 

according to the latest technology and the recog-

nized safety rules.

Danger may nevertheless result for the user or 

others or for the screw compressor air end system 

during its use.

Any use other than described in the chapter 

"Purpose" is considered improper.

ROTORCOMP shall not be liable for any damage 

or injuries resulting from such improper use.

We shall not provide any guarantee whatsoever 

for malfunctions and damage resulting from failure 

to comply with the operating manual.

The manufacturer reserves the right to carry out 

further technical developments without prior 

notice.

Always specify the model and the complete serial 

number from the nameplate in all correspondence.

ROTORCOMP shall assume no liability whatso-

ever for damage or injuries which occur during 

handling, operation, maintenance work or repairs 

due to a failure to comply with the safety instruc-

tions to proceed with the usual care and caution, 

even if this is not expressly mentioned in this oper-

ating manual. 

Содержание EVO15





































Отзывы: