background image

Operating Manual - 

EVO

®

 Line

[en] 07/2020

7.5

7.5 Maintenance intervals

Caution:

The frequency of the maintenance intervals (oil 

change, replacement of oil filter, fine separator 

cartridge and air filter element) varies depending 

on the application and the operating parameters. 

Depending on the design of the system, mainte-

nance interval should therefore be specified by the 

compressor manufacturer. These must be given 

priority. It is advisable to conclude a maintenance 

agreement. The following table provides an over-

view of the reference value for the screw compre-

sor module.

Maintenance intervals 

(Bh = operating hours)

Maintenance work

Before commissioning

Before start-up check correct assembly of the screw compressor stage,

of drive elements and connections of compressed air and oil supply.

Check the presence and position of valves and shut-off valves.

Check oil level in the oil tank.

Follow procedures for initial start-up and recommissioning.

Once after 50 Bh

Check shaft seal for leakage once after 50 operating hours

Every 100 Bh 

Check the shaft seal for leakage every 100 operating hours

Every 1,000 - 6,000 hours 

depending on application, 

at least every 12 months

Replace oil and oil filter

Every 20,000 Bh

Check rotor bearings for play (axial and radial)

Depending on load replace bearings and seals as a precaution

Содержание EVO15





































Отзывы: