background image

Operating Manual - 

EVO

®

 Line

[en] 07/2020

4.1

4

Transport

4.1 Delivery and packing

The system is delivered in suitable packing in 

accordance with the selected shipping method 

and delivery conditions.

4.2 Transport damage

Regardless of the care taken at the factory, the 

screw compressor air ends may be damaged 

during transport. Therefore, the screw compressor 

air ends should be checked for damage following 

each transport.

Caution:

A damaged screw compressor air end must not be 

put into operation under any circumstances. In 

case of transport damage, damage claims must 

be secured in your interest by calling in represen-

tatives of the transport company promptly for 

determination of damage, i.e.:

A) Damage or loss

– must be certified with a corresponding note on 

the freight bill before the merchandise is 

accepted. With rail transports, a 

record of the 

facts

 must also be requested from the railroad.

– With postal consignments, the damage must 

be certified in writing by the postal service 

before accepting

 damaged packages etc.

B) In case of damage which cannot be recog-

nized immediately

– which are discovered during unpacking, the 

carrier must be notified 

immediately

 and 

in 

writing

.

– If possible, leave packing materials and dam-

aged products in an unaltered state until the 

facts are recorded.

– Above all, comply with the complaint deadlines.

Note:

Each product is checked in accordance with the 

type and quantity prior to shipment. Should you 

nevertheless have a reason for complaint, please 

specify the Order No.

Содержание EVO15





































Отзывы: