pre-installed when you purchase a new
switcher.
The sequence is selected either through the
Pattern Selection Menu, or by entering the
sequence number on the keypad.
Keep the following in mind:
Keep the following in mind when working with
DVE wipes:
• The switcher dynamically allocates DVE
channels to produce the wipe effect. If there
are not enough channels available, a dissolve
is performed instead.
• There is a single frame of delay at the start
of DVE transitions.
To Set Up a DVE Transition
1.
Press
DVE
on the Transition module.
Tip:
When you press DVE on the Transition Module,
MEx
WIPE#
is shown on the display of the Global Memory
Module. Enter the number of the sequence you want to load
using the keypad on the Global Memory Module and press
ENTER to load the sequence.
2.
Select the sequence you want to use for the
transition.
3.
Press
Direction
to select if the wipe moves
forward (
Fwd
) or in reverse (
Rev
).
Note:
The Direction and Flip Flop features are only
available for background transitions. The buttons are gray
if a key only transition is selected.
4.
Press
Flip Flop
to select if the wipe moves
in the opposite direction with every
transition (
On
), or always moves in one
direction (
Off
).
Fade to Black
Fade To Black allows you to cut or fade the
entire output of the control panel to black. This
can include just the MEs assigned to the control
panel, depending on how you have Fade to Black
set up, and what MEs are assigned to your panel.
Downstream Keyers are also affected by the
Fade to Black.
If you are controlling an Audio Mixer from the
switcher, performing a Fade to Black will not
change the level of the on-air audio channel.
Instead, Fade to Black turns off the Master Audio
Control on the Audio Mixer.
Fade to Black only affects the MEs that are
assigned to your control panel, and that Fade to
Black is turned on for. If more than one control
panel has the same ME assigned to it,
performing a fade to black sets that ME to black
on all control panels.
To Fade to Black
The personality option must be turned on to
perform a Fade to Black.
1.
On the Fade to Black module, press
CUT
to
cut to black, or
FADE
to dissolve to black.
The dissolve is performed at the Fade Rate.
When the switcher is at black, the
FADE
button is lit with the on-air color, and all the
on-air indicators for MEs or Keyers that
were on-air are flashing.
2.
Press
CUT
to cut out of black, or
FADE
to
dissolve out of black. The dissolve is
performed at the Fade Rate.
Preset Background
Insert a transition to black as the next transition
without losing what is currently selected as the
next transition.
When a Preset Background is selected as the
next transition, the ME is set as follows:
• The current next transition setting, including
keyers, are stored.
• Sources selected on each bus is stored.
• The background and any keyers that are
on-air are selected for the next transition.
• By default, dissolve is set as the transition
type, but a wipe can also be used.
To Perform a Preset Background Transition
1.
Press and hold the
PST BKGD
button.
2.
Press the source button on the preset bus
for the source you want to use for the preset
background.
When you release both the buttons, the
preset background source is selected on the
preset bus.
3.
Select a dissolve (
DISS
) or wipe (
WIPE
) as
the transition type.
4.
Perform the transition.
After the transition is complete, the
PST
BKGD
button is turned off and the source
that was selected on the preset bus before
the preset background is again selected.
Ultrix Acuity Operation Manual (v10.1) — Transition • 37
Содержание Ultrix Acuity
Страница 1: ...Ultrix Acuity Operation Manual v10 1...