Rosemount 8732 Series Скачать руководство пользователя страница 56

Страница: 56 / 190

Reference Manual

00809-0100-4663, Rev BA

January 2010

Rosemount 8732

4-18

Block Mode: Target

Operator requested mode for the function block. Only one selection may be
made. Options include:

Auto

Use this mode when all configuration changes to the block are complete and
the transmitter is ready to be returned to service.

OOS

Out of service mode. Use this mode when making configuration changes to
parameters found in the function block. This removes the transmitter from
operation until the mode is set back to Auto.

Block Mode: Actual

This is the current mode of the function block. This mode may differ from the
Target mode based on operating conditions.

Block Mode: Permitted

This parameter defines which modes are available for a given function block.

Block Mode: Normal

Displays the mode that the function block should be set to for normal
operation.

375

Transducer Block, Mode

375

Transducer Block, Mode

375

Transducer Block, Mode

375

Transducer Block, Mode

Содержание 8732 Series































































































































































































Результаты поиска

Содержание 8732 Series

Отзывы:

Похожие инструкции для 8732 Series

Бренды по названию

Популярные бренды

Rosemount 8732 Series, Справочное руководство

Результаты поиска

Содержание 8732 Series

Отзывы:

Похожие инструкции для 8732 Series

Бренды по названию

Популярные бренды