manualshive.com logo in svg

Rosemount 8732 Series, Справочное руководство

Поделиться
Скачать
Rosemount 8732 Series Скачать руководство пользователя страница 122

Reference Manual

00809-0100-4663, Rev BA

January 2010

Rosemount 8732

C-2

LICENSING AND 
ENABLING

All non-basic diagnostics must be licensed by ordering option code D01, D02, 
or both. In the event that a diagnostic option is not ordered, advanced 
diagnostics can be licensed in the field through the use of a license key. To 
obtain a license key, contact your local Rosemount Representative. Each 
transmitter has a unique license key specific to the diagnostic option code. 
See the detailed procedures below for entering the license key and enabling 
the advanced diagnostics.

Licensing the 8732 
Diagnostics

For licensing the advanced diagnostics, follow the steps below.

1.

Power-up the 8732 transmitter

2.

Verify that you have 1.01.001 software or later

3.

Determine the Device ID

4.

Obtain a License Key from your local Rosemount Representative.

5.

Enter License Key

6.

Enable Advanced Diagnostics

TUNABLE EMPTY PIPE 
DETECTION

The Tunable Empty Pipe detection provides a means of minimizing issues 
and false readings when the pipe is empty. This is most important in batching 
applications where the pipe may run empty with some regularity.

If the pipe is empty, this diagnostic will activate, set the flow rate to 0, and 
deliver a PlantWeb alert.

Turning Empty Pipe On/Off

The Empty Pipe diagnostic can be turned on or off as required by the 
application. If the advanced diagnostics suite 1 (D01 Option) was ordered, 
then the Empty Pipe diagnostic will be turned on. If D01 was not ordered, the 
default setting is off.

Tunable Empty Pipe 
Parameters

The Tunable Empty Pipe diagnostic has one read-only parameter, and two 
parameters that can be custom configured to optimize the diagnostic 
performance.

375

Transducer Block, Diagnostics, Advanced Diagnostics, Licensing

AMS Tab

License

375

Transducer Block, Diagnostics, Advanced Diagnostics, Licensing, License Key, 
Device ID

AMS Tab

License

375

Transducer Block, Diagnostics, Advanced Diagnostics, Licensing, License Key, 
License Key

AMS Tab

License

375

Transducer Block, Diagnostics, Diagnostic Controls

AMS Tab

Diagnostics

375

Transducer Block, Diagnostics, Diagnostic Controls

AMS Tab

Diagnostics

Содержание 8732 Series































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды